Questions tagged [crankshaft-pulley]
The crankshaft-pulley tag has no usage guidance.
12 questions
1
vote
1
answer
174
views
Did I cause my timing to slip by rotating my crankshaft pulley bolt CCW?
I was replacing the alternator on my 2014 Ford Fusion 1.5L, mistook the crankshaft pulley bolt for my tensioner. At first I rotated the crankshaft pulley bolt CW before realizing it was the wrong bolt ...
1
vote
1
answer
320
views
I have a required torque of 30nm +100° +-5°, I have a torque-wrench 40nm-210nm. Can I convert the required setting to my TW somehow?
I have a required torque of 30nm +100° +-5°, I have a torque-wrench 40nm-210nm. Can I convert the required setting to my TW somehow?
I'm hoping there is some kind of conversion whereby the 30nm can be ...
3
votes
1
answer
485
views
Is there any particular advice on crank-bolt lubrication I should know?
I have a new crank-bolt to install following a timing-belt replacement.
Should I be lubricating this bolt? And if so, what kind of lube should I look for?
-1
votes
1
answer
170
views
Is there a wrong position or engine phase to insert a locking pin?
K7M engine (Renault Sandero)
During a timing-belt and tensioner change, I used a locking-pin(an 8mm bolt) to hold the engine while breaking loose the crank-pulley bolt.
Not being an experienced mech', ...
2
votes
2
answers
323
views
What cleaning solvents are appropriate for crank bolts, pulleys and gears?
Have bolts and parts(crank gear, shaft-end, bolts).
Which solvents can I use to clean them up a bit? And do I need to lubricate any of these?
I have Zylene-based wax, parafin, turpentine, motor oil, ...
0
votes
0
answers
129
views
2020 Kia Sportage 2.4l wobbling crankshaft pulley
I am considering purchasing a used 2020 Kia Sportage with the 2.4 liter engine. I opened the hood when it was idling and noticed the crankshaft pulley was wobbling. It wasn't making any noise and it ...
2
votes
1
answer
2k
views
Nissan Crank bolt: reverse thread?
Engine HR12DE
Nissan Micra K13 2011
Hello, I’ve been trying to remove the crank pulley bolt and it won’t come off. I also tried blocking it with a handle bar and cranking the engine, the trick didn’t ...
1
vote
1
answer
3k
views
Method to remove crankshaft pulley
I am attempting to remove the bolt that holds the crankshaft pulley. However, even with a long bar, the car in sixth gear and the brake on, it was not possible to undo the bolt. I found online that ...
2
votes
2
answers
549
views
Removed the harmonic balancer with a wooden block and a rubber mallet - did I damage anything
I have the engine out of the car and I had to remove the harmonic balancer, I did not have the proper puller and for some reason I used a wooden piece and a rubber mallet to tap the balancer off the ...
5
votes
2
answers
2k
views
Does this harmonic balancer / crankshaft pulley look damaged?
Does this harmonic balancer / crankshaft pulley look damaged?
To me it looks like the rubber between the inner and outer parts is at least cracked if not completely separated.
3
votes
0
answers
184
views
How to remove vibration damper from a Volkswagen 1.8 TSI (EA888) Engine?
How do you remove the vibration damper from a 2010 Passat CC 1.8 TSI engine? Which direction do you turn the bolt to remove it? Clockwise OR counterclockwise?
3
votes
2
answers
656
views
V6 Toyota 4Runner - Broken Crankshaft Pulley
I am new to working on cars and this is the first timing belt change I have attempted. I was trying to remove the crankshaft bolt using a breaker bar and my pulley broke. Now I am unable to remove the ...