Skip to main content
37 votes
Accepted

Need I press clutch pedal while starting my car in neutral?

It depends on the specific vehicle. Many modern standard transmission cars in the US have a clutch pedal sensor that will not allow you to start the vehicle if the pedal isn't fully depressed. You'...
Bob Cross's user avatar
  • 24.4k
27 votes

Need I press clutch pedal while starting my car in neutral?

Being from Canada, I feel compelled to mention that if you do not depress the clutch while starting when it is at all cold out (let's say < 0 Celsius) you will notice the starter motor labouring ...
jkf's user avatar
  • 422
24 votes
Accepted

My (manual) transmission won't engage any gear 1 day after escaping bog

I've narrowed it down to the most likely possibilities: You may have burned out your transmission, or cracked the casing and lost all your fluid, in which case you're going to have to replace the ...
GdD's user avatar
  • 17.1k
21 votes
Accepted

Motorcycle moves forward when in gear even with clutch lever pulled

This is common among all motorcycles that have a "wet" clutch system. What that means is that the clutch is surrounded by fluid, usually engine oil. Even though you have the clutch pulled ...
jwh20's user avatar
  • 12.1k
16 votes
Accepted

What happens when I shift gears without pressing the clutch in a manual transmission while the car is running?

It is not a good idea to change gear without using the clutch, you will cause unnecessary wear that will end up causing an expensive bill. When you select a gear, there is a component in the gearbox ...
HandyHowie's user avatar
  • 25.4k
15 votes
Accepted

How does the clutch prevent stalling?

The engine is connected to the drive wheels through the transmission. In order to continue to run (not stall) an engine needs to turn at a minimum speed (for instance 600 RPM). As a car slows down, ...
Glen Yates's user avatar
12 votes
Accepted

94 Toyota Pickup hard to put into gear after clutch in too long

If its a hydraulic clutch, it may be bleeding off, either a leak or a bypassing clutch master cylinder.
Moab's user avatar
  • 7,990
11 votes

Should I depress the clutch pedal when braking to a stop?

No other problem than using slightly too much fuel. The recommended way to brake is to use the current gear and keep the clutch engaged during braking until idling RPMs at what point one presses the ...
juhist's user avatar
  • 14.6k
11 votes
Accepted

Is it worth replacing the entire clutch assembly when the clutch release bearing fails?

At ~110k on the clock it's quite likely that it's the original clutch, and if so you're going to be significantly closer to the end of the clutch's life than the start. Given the big labor cost/...
motosubatsu's user avatar
  • 10.2k
9 votes

What mechanical action is heel and toe (clutchless) shifting trying to accomplish?

I'm going to expand on rpmerf's answer, where he has disambiguated between Heel and toe and clutchless shifting. I'l briefly explain the driving technique only to better illustrate what it hopes to ...
chilljeet's user avatar
  • 2,196
9 votes
Accepted

Is it correct to downshift to brake?

So there are several aspects to keep in mind if you use engine braking. No brake lights! Don´t do this when somebody sits at your back! Don´t over-rev. Only downshift to an appropriate gear. Never ...
Daniel's user avatar
  • 1,072
8 votes
Accepted

What would happen if you shifted into reverse while you are going forward?

My theory is that the engine would be forced to rotate the other way around, wouldn't it? Then, because of that, the engine would stop, and therefore it will "generate" a lot of force to the ...
Jeep Cherokee Rescue Society's user avatar
8 votes

my motorcycle take more time to accelerate

Your clutch might be bad If your clutch is slipping then the RPM's of the bike can go up but the bike doesn't accelerate as the clutch slips. Many times a clutch will start slipping when the engine ...
DucatiKiller's user avatar
  • 32.9k
8 votes
Accepted

Why don't cars have multiple disk clutches as motorcycles do?

It all comes down to size. There is one thing which makes a clutch work, whether wet or dry. It comes down to friction. There are two ways to achieve the friction needed to transfer the energy from ...
Pᴀᴜʟsᴛᴇʀ2's user avatar
7 votes
Accepted

What are the differences between a normal and an anti-hopping/slipper clutch?

On a regular clutch, the inner hub that drives the gearbox is a single casting. Clutch plate pressure is solely applied via the outer pressure plate and springs. On a slipper clutch, the inner hub is ...
Roger Mellie's user avatar
7 votes

2012 Mazda3 shifts gears but won't move

If the clutch cable was bad you wouldn't be able to put in in gear with the engine running. Based on what you have described you have a bad clutch.
Move More Comments Link To Top's user avatar
7 votes
Accepted

Never declutch while braking at higher speeds: meaning

There are two things to think about here. (1) On a bike, engine braking only acts on the back wheel. If you press the clutch while you are braking hard, you change the "balance" of the ...
alephzero's user avatar
  • 2,954
6 votes
Accepted

Car rattles at low RPM

Sounds like it's possibly involved with the transmission and/or clutch. But first, I would check all the heat shielding on the car to make sure that's not a factor. When the transmission is engaged (...
Jeep Cherokee Rescue Society's user avatar
6 votes
Accepted

Wobbly clutch pedal

An "unhappy" amount of movement in the pedal doesn't seem right, especially in a new car. If no one here can give you a definitive answer, and looking at the pedal mount and linkage under the dash isn'...
dlu's user avatar
  • 14.5k
6 votes
Accepted

What is the purpose of the rubber cup in the master clutch reservoir?

The purpose of the rubber cup is to allow for a seal on the master cylinder reservoir, and then to allow for fluid to escape down into the slave cylinder as needed. It allows the fluid to easily ...
Pᴀᴜʟsᴛᴇʀ2's user avatar
6 votes
Accepted

Why can some cars pull up a hill with just the clutch?

You've exposed a combination of two things: high torque at low engine RPMs + high mechanical advantage => forward motion without requiring additional throttle (where "high" is defined to be "high ...
Bob Cross's user avatar
  • 24.4k
6 votes
Accepted

Disengaging gear when braking/Coasting

If you're coming to stop, the inertia of the vehicle drives the wheels. This keeps the engine spinning if you don't touch the clutch until the absolute last moment. In your case it sounds like this is ...
Eric Urban's user avatar
  • 1,286
5 votes
Accepted

What is happens to the brakes when an automatic drives below the speed for 1st gear with no added gas?

One thing to keep in mind here is that you're looking at the same problem either way – with a manual you're wearing the friction materials in the clutch, with an automatic the wear is happening to the ...
dlu's user avatar
  • 14.5k
5 votes

What are the pro's and con's of compression braking vs. exhaust braking?

Attributes of Exhaust (Jake brake) and Compression Brakes Compression (Jake) Brake Jake brakes slow a vehicle by releasing pressure Jake brakes are operated at the valve train. Jake brakes open the ...
DucatiKiller's user avatar
  • 32.9k
5 votes
Accepted

Hand turned the crankshaft while in gear. Clutch damage?

It's fine I did a similar job on a 2003 model recently. I kid car. Luckily, I didn't have any bent valves to deal with. Turning the engine over with the head off and the car in gear won't hurt ...
DucatiKiller's user avatar
  • 32.9k
5 votes

I think my clutch is failing, how can I tell what needs to be replaced?

If it is a slipping clutch it will get worse soon, and you will know for sure, from your description, yes it is slipping. Yours is a FWD car, they are a bit more difficult than a RWD most of the time,...
Moab's user avatar
  • 7,990
5 votes

Riding motor cycle in a slow moving traffic

I would argue that wear and tear on the clutch is a secondary consideration. There are too many idiots not paying attention on the road, and it's faster to pull away in first, than from neutral. That ...
Leliel's user avatar
  • 583
5 votes

2012 Mazda3 shifts gears but won't move

If you can depress the pedal and select gears with the engine running, but then don't have any drive once you have selected a gear, then I'm afraid it sounds very much like the clutch has gone. It's ...
Nick C's user avatar
  • 28.8k
5 votes

VW T5 8000 Miles Clutch Burnt Out

The bellhousing (the part of the transmission that is closest to the engine, so named because it is bell shaped) should be dry, but there are 3 potential fluids that could be leaking into, and ...
Zshoulders's user avatar
  • 1,646
5 votes

Need I press clutch pedal while starting my car in neutral?

I drive an old landrover with a 202" straight six. And I was taught to start in neutral with the clutch out. This means the starter has to spin more mass, but that mass will help the engine turn ...
Criggie's user avatar
  • 2,978

Only top scored, non community-wiki answers of a minimum length are eligible