Questions tagged [obd-ii]

On-Board Diagnostics-II (OBD-II). Questions usually involve scan tools, their use and their compatibility, as well as how to interpret Diagnostic Trouble Codes (DTCs).

Filter by
Sorted by
Tagged with
0
votes
0answers
24 views

I need to add an OBD-II based accessory to a OBD-port-less and ECU-less car

My guess is the accessory would work fine if only provided power (no need for it to receive diagnostics info, just to turn on to perform its function). Would it be possible to connect pins 16 and 4 to ...
0
votes
0answers
37 views

mechanic can't reproduce trouble when car is at shop… need to record OBD data when problem occurs while driving

I brought my car in for servicing, but the mechanic can't reproduce the problem. I want to log OBD data as the problem occurs. I would then provide this captured data with the car when it goes back ...
2
votes
0answers
29 views

P0638 code on 2 different generic scanners but service center says it's the readers that are faulty and the car is fine?

I recently purchased a 2nd hand Kia Rio LX 2018 with 24k miles on the clock. The car drives well, the check-engine light is off, I had a pre-purchase inspection done on it (Lemon Squad) and their ...
0
votes
1answer
19 views

Can issue with P0736 error code produce EM Interference?

I have had an issue with a car where phone GPS doesn't work inside the vehicle. I have just connected my OBD2 diagnostics tool and ran it. I got back 3 issues: P0736 ME - Motor electronics: ...
0
votes
0answers
14 views

KWP OBD2 ECU Target Address

When communicating with an ECU via the OBD2 port using the CAN protocol, we have a well known address $7DF. Irrespective of the make and model of the car this address can be used to read MODE 1 ...
2
votes
1answer
164 views

Using OBD to control add-on lights

I have just purchased a 2021 Ram 1500 Bighorn and plan on adding side lights under running boards. These lights are led strips with amber for marker and turn, red for running lights and white for ...
0
votes
1answer
30 views

How do I decode BMW CAN data (over OBDII)

I'm using an ELM327 type device. I'm trying to poll and decode data on my BMW i3. I'm using some of these resources as a reference: This post breaks down the init I need to do. This further post ...
0
votes
0answers
12 views

OBD2 Mode 3 No Response

I am communicating with my car OBD2 port with STM32 microcontroller board and got success to get response to basic PIDs such as Service 01 and 02 and even got response of service 09 PID 02 to get 17 ...
1
vote
0answers
27 views

Central locking in Mercedes-Benz Vito W639 is temperamental when GPS is attached to central locking

I have a fleet of vehicles (Hyundai, Mercedes, Toyota, Volkswagen, Honda) all which have a GPS tracking device attached to their OBD2 port. Of this fleet, a subset of the vehicles are Mercedes-Benz ...
0
votes
0answers
21 views

Mercedes C180 Kompressor ODB 2 P0170 & P171 errors

Recently been having problems with my 2004 Mercedes C180 Kompressor. It was driving well, sometimes at stoplights, it would rev inconsistently but would only be only a few 100 rev/min. This wasn't a ...
0
votes
1answer
40 views

Is there a non-USB-OBD2 adapter made for reprogramming (CAN/ISOTP)?

I'm working on an ECU reprogramming and coding app (iOS, Android, etc.) for a client who is part of the automotive tuning scene. I have been trying out dozens of OBD2 adapters, but most of them fall ...
0
votes
0answers
23 views

Cannot connect to gateway node of CAN bus through OBD2 port

I wanna connect to can bus of my car. I read in the manuals that obd2 is hooked to high speed can bus of something called CCU node and this CCU node acts as gateway between HS and LS canbus. When i ...
0
votes
1answer
35 views

Can an OBD2 tester do a battery load test?

This Autophix device device was suggested by a review as the best of five battery testers. The text implied that includes testing cranking amps. But it can only connect to the computer—has no way to ...
0
votes
0answers
44 views

Wireless control of trailer board lights

Is there a (Bluetooth?) OBD module that can transmit to a receiver that remote controls a car trailer board lights ? I have seen the magnetic bluetooth "stick on lights" that are powered by ...
0
votes
0answers
40 views

Clear OBD-II codes automatically? Either with sollid-state device or smartphone app/widget

Been using an ELM327 adapter with various apps to clear OBD-II trouble codes. While this works, wondered if there is an app or device which can do the following without intervention: Clear all obd-...
0
votes
1answer
65 views

What does OBDII fault code P0120 really mean?

What does OBDII fault code P0120 mean? The device said: "TPS/Pedal Position Sensor A Circuit Malfunction". The problem is that TPS stands for: "Throttle-body Position Sensor, which sits ...
1
vote
0answers
59 views

2006 Honda Civic Hybrid, error lights on dash, and codes

A few months ago, my Civic Hybrid started giving me issues. When I start it in the morning, I have to hold the key for a few seconds before the engine catches. Once the engine is running, my IMA light,...
7
votes
1answer
1k views

Would OBD-II devices drain the battery when used 24/7?

There are many OBD-II devices out there that can scan and/or monitor real-time data about your car. Most of these devices are readable via USB or Bluetooth. Either USB or Bluetooth, both require some ...
0
votes
1answer
86 views

How does a OBD II misfire detection monitor know “exactly” which cylinder is misfiring?

I do know that magnetic pick-up coils are used to detect crankshaft position and these sensors are used to tell which cylinder is misfiring. These magnetic pick-coils do not produce a smooth & ...
0
votes
1answer
39 views

how to check car for impending failures? [closed]

My kia Sorento 2007 failed on me multiple times. Each time disabling the car and putting the driver in danger harmonic balancer alternator radiator and water pump in each of those failures, I had ...
0
votes
0answers
42 views

OBD2 for car customization

i was wondering if it could be possible use CAN protocol to automate some of my car (Suzuki Swift 2016 1.3 DDiS) processes, such as close windows when door get locked. I found lot of applications/...
1
vote
0answers
414 views

Run a forced DPF regeneration using OBD-II diagnostics

Our Jeep Grand Cherokee 2015 has problems with its exhaust filter. The error says we should drive safely at highway speeds to remedy but even after driving a few hours, it does not recover. It is ...
1
vote
1answer
61 views

What is typically involved to repair a internal combustion engine that has a cylinder misfiring?

I have a vehicle with a cylinder misfiring (according to my OBD-II code reader). I have decided to have a mechanic repair it, as I have never performed a similar motor vehicle repair. Note that the ...
1
vote
0answers
55 views

2009 Volkswagen Jetta TDI diesel 2.0L

I have 2009 Volkswagen Jetta TDI diesel 2.0L, they saying this car required CAN bus system instead kwp2000. My question is: How does the protocol Id change? Maybe ECU is defective? Some people told me ...
1
vote
1answer
194 views

P0491 Secondary Air Injection System Insufficient Flow. Stumped

My VW CC 2010 is having a CEL with the code P0491 which means the pressure sensor is not detecting enough air being pumped from the intake into the exhaust. No other codes. No problems since this is ...
0
votes
0answers
166 views

2010 Ford focus Zetec 1.6 Diesel U0073 DTC

I've had my 2010 Ford Focus Zetec 1.6 TDCi for a week now. There is the DTC U0073 (control module communication Bus 'A' off) on it. There is no issues with the car,no warning lights on dash, drive is ...
2
votes
1answer
58 views

OBD-II Scanning Bluetooth | Are Fault Codes Encripted?

I bought JDiag Fastlink OBD II scanner which is based on ELM327 based OBD II scanners. I noticed that the scanner was able to read all the instrument panel reading such as fuel level, engine ...
0
votes
2answers
339 views

Increase volts at OBD port

My fixd scanner only says low voltage. How can I increase the volts at OBD connection my check engine light is on trying to get code. 1999 GMC Sierra 2500 with a 5.3 litre Vortec engine Scanner ...
0
votes
0answers
96 views

Mk6 Ford Fiesta 1.25 OBII oxygen sensor readings

Plugged my Mk6 Ford Fiesta into Forscan Lite today, and got the following faults below. Was curious to see that both the 021 and 022 flatline at near zero volts at 2000 rpm. That's not normal is it? ...
0
votes
0answers
73 views

Are OBD-II devices capable of controlling acceleration and top speed of a car? [duplicate]

I have been searching for a while for some specific type of OBD-II devices that can, besides performing the usual diagnostics, also do the following: GPS track the car online Has the ability to set ...
1
vote
1answer
414 views

Will my car pass emissions if all monitors pass scanner except EVAP monitor

I had toyota remove a P code off my 2010 1.8L corolla after a repair. I need to pass emissions in Arizona in the next 2 weeks. I went to AZ and they let me borrow the scanner so I plugged it and ALl ...
0
votes
0answers
214 views

What is “transmission slip ratio” and is it normal to have anything other than 1.0?

I got a 5.4 Ford econoline 1998 edition. I got me a odb2 code readin app with the bluetooth on it... and I also paid extra to unlock the premium Ford specific data... all kinds of stuff in there. In ...
0
votes
1answer
887 views

Is it possible to clear “permanent codes” on a Volkswagen Jetta?

I was inspecting a 2011 Volkswagen Jetta today and saw on my OBD reader that it had two misfire codes, if I remember correctly P0302 cylinder 2 misfire and P0300 multiple cylinder misfire. The check ...
0
votes
1answer
134 views

Feelin' a misfire but ain't showng no misfire in the computer

I swears when I turn on my van just sitting there I feel a misfire more often than any good person should. In my opinion, I shouldn't be feeling any weird shakin or nothin. When she's been driven a ...
1
vote
2answers
43 views

Data captured when an error code is generated

I have a 2015 Ram 1500 that has just over 60,000 miles (107000 km). They did a diagnostics and there are several transmission error codes. Is the mileage tracked when the error code is captured. ...
0
votes
0answers
79 views

Which DLC terminals are known as DLC bias terminals (or should it be DLC Bus terminals)

This is related to Test 5 of this question: OBD II Scanner refuses to communicate with the vehicle! Funny that I should be asking this but then .....it happens Unfortunately, I cannot remember. I'd ...
0
votes
0answers
35 views

22 OBD codes 2008 Chevy Tahoe :D Help

I just inherited a 2008 Chevy Tahoe LS 5.3L V8 with 239,730 miles. When scanning for codes it listed about 22 codes. I know the obvious thig to do is to take it into a mechanic but i want to see if ...
0
votes
1answer
106 views

Get Brake pedal position from generic ELM 327 BLE OBD dongle [closed]

What is the code to get the brake pedal position using the generic ODD2 (ELM327) dongle
0
votes
3answers
105 views

Compiled list of OBD-II protocols used by various vehicles

Has anyone compiled list of OBD-II protocols (physical layers) used by various vehicles? they're required to be J2534 compatible but what about manufacturer specific pins? is it even common for ...
4
votes
3answers
1k views

How useful is a low-end corded OBD-II reader for inspecting a used car?

I purchased a low-end OBD-II reader from Wal-Mart a few months ago. Now I'm in the market to purchase a used car and I was wondering how useful the reader will be when I go to look at the vehicle. Of ...
0
votes
0answers
54 views

Volkswagen GTI OBDII Readiness

I have a 2015 Volkswagen GTI SE (2.0T) which is (a little over) due for an emissions test. A few weeks ago I had some rear-end bumper damage repaired, and while in the shop they cleared the trouble ...
0
votes
1answer
320 views

Cannot connect OBD devices to ECU on Toyota vehicles

I have two ODB devices. One is ELM327 Wifi OBD2 and the other one is OBDLink LX Bluetooth. My problem is that none of the OBDs connect to Toyota cars. More specifically: I have tested the two OBD ...
1
vote
1answer
2k views

OBD2 Scanner can not detect ECU 2002 Mitsubishi Lancer

I bought a OBD2 Bluetooth scanner online. However, when I connect it to the OBD2 port in the car, the app while connecting to the OBD2 scanner gives an error message that it cannot connect to the cars ...
2
votes
0answers
249 views

Engine jerks at certain RPM - Misfire & fuel system over pressure [P000F, P0302]

My Audi A5 1.8t has started having some hiccups after an engine job (Changed valves, timing chain & camshaft intake side) The car starts fine, it sounds fine, but it has the following problems: ...
2
votes
1answer
87 views

Using a device with external power and receive data from the CAN bus

I want to keep a device in always on situation in the car. I do not want the device to drain the car battery. The car is used at least once in two days and the current consumption of my device is ...
0
votes
0answers
146 views

Suzuki Swift Sport and ODBii

I recently purchased a new Suzuki Swift Sport, and wanted to use the Torque App for some checking ( mostly enjoy parameter reading, graphs.... ) but my wifi adapter was unable to communicate with the ...
3
votes
1answer
931 views

Can I trickle charge battery through OBD2 port 2007 civic

Trying to determine if 2007 civic OBD2 port is live with key off so I can trickle charge with a solar panel
0
votes
1answer
1k views

Can one set idle rpm through a commercial OBD diagnostic tool?

I'm talking about "permanently" setting the engine's ECU to maintain an idle RPM of my choice, say, 1200 or 1500? (by "permanently", I mean something that would be maintained after power cycling) If ...
1
vote
1answer
222 views

Tacoma inducing monitors after resetting ECU

My 2006 Toyota Tacoma had a check engine light, which I decided to try to turn off for the purposes of vehicle inspection. I thought that was okay because the problem was not emission-related but ...
2
votes
2answers
74 views

Can I Connect dashcam Blackvue DR900S on OBDII connector in Volvo XC70 2015?

Do I get 12V on OBDII pin 16 without ignition ON?

1
2 3 4 5
9