Questions tagged [mitsubishi]

Japanese carmaker, known for the Lancer and Evolution models

Filter by
Sorted by
Tagged with
0 votes
0 answers
21 views

Alternator doesn't charge the battery when idle with head lights on

My car is a Mitsubishi Magna TH 1999 3.5L Auto. The alternator gives no voltage at idle with headlights & fan on. The battery gets drained. The alternator warning light pops up. If revved a little ...
Raj's user avatar
  • 1
0 votes
0 answers
10 views

No crank , no start Lancer Gt 2015

2015 Mitsubishi Lancer GT wont crank from the ignition switch also , radio won’t come on and key fob isn’t working so I’m manually using the key inside to turn it .
Michael 's user avatar
6 votes
1 answer
308 views

Mitsubishi Montero Sport 2000, 4 wheel drive engages, but the indicator flashes

I have an issue when i engage my 4wd gear to high or low, the 4wd indicator keeps flashing. However, the 4wd works perfectly. I've changed the 4wd solenoid that resides in the engine bay (which is a ...
Hasitha Shan's user avatar
0 votes
2 answers
29 views

Montero/Pajero consistent humming at idle and at speed

I have a 2001 Pajero/Montero III 3.5v6 GDI automatic which developed a tiny hum about 8 months ago. This hum has been growing louder ever since and is at a point where you can very easily hear it ...
TheLegendaryCopyCoder's user avatar
1 vote
1 answer
37 views

How do I fix a parasitic power drain on 2018 Mitsubishi Outlander Sport

I am reaching out desperately looking for help. I purchased this vehicle in April of 2022 and have been through 5 batteries. I tried contacting the dealership and they told me that the battery wasn’t ...
Savanah Morton's user avatar
1 vote
1 answer
19 views

Can Dexron IID ATF be used in place of Dexron II ATF?

My vehicle manual states I must use Dexron II ATF fluid for my power steering. When I shop around, I often find Dexron IID ATF locally. Can I use this, or must I find something without the D after the ...
TheLegendaryCopyCoder's user avatar
0 votes
1 answer
33 views

Hesitation/ rough idle for couple of seconds on cold starts

I have a Mitsubishi Montero sport 2003 with the 6g72 3.0l v6 engine. Recently it started to develop an issue where it idles rough for like 2-3 seconds only on morning cold starts. After that the car ...
Hasitha Shan's user avatar
-1 votes
1 answer
30 views

2001 Mitsubishi Mirage just died at red light

My son has a 2001 Mitsubishi Mirage and as he pulled up to a red light it died.. No pre warning, no hesitation nothing it just died . After that him and another gentleman pushed it out of the road and ...
Manda8306's user avatar
1 vote
1 answer
27 views

Engine swap & ecu

So I was thinking about putting a vw 2.0t into my 1999 eclipse gs. Would I have to get a standalone ecu or can I wire in the engines ecu in place of the eclipses oem. I'd be able to figure everything ...
QuickSixX42's user avatar
1 vote
1 answer
49 views

AC compressor clutch air gap gets wider by itself after bearing and shaft seal replacement

My parents' 2014 Chevrolet Spin Diesel compressor shaft seal was leaking. We replaced the seal and shaft's ball bearing (located between the seal and clutch plate), add about 44mL PAG oil into the ...
bas's user avatar
  • 11
0 votes
0 answers
33 views

Need help identify the part in the photos. It is from a 2004 dodge Stratus

A friend of mine had her timing belt break and they said this part in the image needs replacing also. We want to order it but don't know what it is named and googling isn't working out so well. The ...
John Lord's user avatar
  • 610
2 votes
2 answers
90 views

Clutch pedal has a step?

The vehicle is a 1993 Lancer Evo idk how to explain this but my clutch pedal sorta has 2 positions? When I press it with little force it stops and I can engage gears. It's a little tough though and a ...
J. Doe's user avatar
  • 63
0 votes
1 answer
85 views

Steering wheel feels wobbly after changing wheels to 215/45zR18

I have a 2009 Mitsubishi Lancer. I was using winter tires of size 205/60R16 and changed into 215/45zR18 summer wheels yesterday by myself. Now when I drive on not-flat uneven or wavy roads , I can ...
Niron Rasanjana Perera's user avatar
0 votes
2 answers
33 views

Imported my car from NZ to Sydney(AU) and doesn’t start after a short journey on hot days unless I wait for half an hour or so to let it cool down?

I’ve imported my Mitsubishi eclipse cross 2018 from New Zealand in January 2023 when I moved to Sydney Australia. It took 3 months to get it due to some delays on import permits. Now problem is, on ...
user2069351's user avatar
0 votes
1 answer
99 views

Mitsubishi Mirage stalling on start, fast idling

Mitsubishi Mirage 2017. When I first start the motor, it turns over and starts, but immediately stalls unless I pump the gas to bring the RPM over 1500 for about 20-30 seconds (normal idle RPM is ...
anonymous2's user avatar
  • 5,245
2 votes
1 answer
133 views

Locating OBDI2 port on used vehicle ( Mitsubishi L200 year: 1998 )

Vehicle model: L200 Make: Mitsubishi year: 1998 ( engine ~2004 from swap ) I am located in the carribean, finding solid used vehicles is a challenge actually that an understatement. Vehicles are ...
Invic18's user avatar
  • 21
0 votes
1 answer
65 views

Can you put hubs in a full-time 4WD vehicle?

Hi everyone I drive a '95 JDM Mitsubishi RVR and it's full-time 4WD. I don't know much about 4WD vehicles but my mate drives a '93 JDM Mitsubishi Pajero (Montero for NA and SA people) and he has hubs. ...
J. Doe's user avatar
  • 63
0 votes
0 answers
56 views

Rod bearing size

My son has a Mitsubishi lancer evo, MR 2.0 turbocharged engine, he spun a bearing. I used plastigage and its reading .003, manual states standard rod bearing is .004 to.010 inch, with a limit of 0.02....
Mike Selby's user avatar
1 vote
1 answer
734 views

Old spare key not starting engine

I have lost my spare key a while ago. I went to the mechanic and asked them to get a new one. They told me that I also need to bring my current main key as programming a new key will invalidate the ...
Yanick Salzmann's user avatar
2 votes
2 answers
888 views

After Change Evaporator had hissing sound from AC vent

I have Mitsubishi Outlander 2016, I have cooling complaint So, I took to garage the technician checked and said there is leakage in evaporator have to change. After changed the evaporator while AC on ...
Anwar Noorullah's user avatar
0 votes
1 answer
63 views

OBD code P0433 problem

I have just had 195000km service on my Mitsubishi Triton 3.5 Ltd V6. They replaced my air filter and I now have a check engine light. Code P0433 on OBD scanner... replace O2 sensor, exhaust leak. No ...
Campbell Smith's user avatar
0 votes
0 answers
672 views

Programming remote key Mitsubishi Colt 2007 1.3

I tried programming the remote key, but I can't get car in programming mode as is described in most YT video's by connecting pins 1 and 4 in OBD and pressing 6 times the emergency button. This should ...
Kr Neki's user avatar
1 vote
1 answer
142 views

Rod knock on first startup in months

2003 Mitsubishi Lancer 150,000 miles, manual 5speed, no check engine lights. This car has been sitting for about a month or two and when I tried to start it, it wouldn’t start so I eventually tracked ...
MikeHoncho1's user avatar
2 votes
1 answer
81 views

Does changing suspension bushing require camber adjustment?

I have Mitsubishi Mirage 1999 or sometimes called Lancer in some countries. I have recently changed the the rear and front suspension and took the car for camber adjustment and alignment. I noticed ...
Carjdn's user avatar
  • 23
0 votes
1 answer
113 views

Engine cylinder 5 misfire

On my Mitsubishi shogun sport van 2002 3.0L V6, There was a slight misfire on cylinder 5. We replaced spark plugs, all the HT leads (Ignition wires) and Ignition coils (all 3). That didn't solve our ...
Dylan Bracey's user avatar
2 votes
3 answers
609 views

How do I remove this bolt to replace my MAF sensor?

I'm trying to replace the MAF sensor in my Mitsubishi 2003 Lancer ES GLi1.8, and it's bolted into a plastic housing that fits the air filter. The bolts are weird, in that they have a head about 2mm ...
e_i_pi's user avatar
  • 153
1 vote
0 answers
1k views

Mitsubishi mirage Code P1590 A/T torque reduction req. comm

The check engine light on my mitsubishi mirage is on and upon scanning the codes, I am getting the following codes: U0131 EPS CAN timeout U0101 T/M CAN timeout U0121 ABS/ASC CAN timeout P1590 A/T ...
Sher Chuha's user avatar
0 votes
1 answer
861 views

Mitubishi Outlander 2018. Replacing SIM card

Whatever I'm doing I'm not find the SIM card in my car. I removed the glove box (and see the white computer behind it. I removed the plasic below the glove box and still doens't find the SIM card, or ...
Aminadav Glickshtein's user avatar
3 votes
1 answer
1k views

How can I turn on the airbag on Mitsubishi Outlander without a key?

In the manual it is written to insert the key for switching. But we have keyless car (just click the start button), and we don't have keys. Is there an alternative way? I tried using a knife, but it ...
Aminadav Glickshtein's user avatar
1 vote
0 answers
97 views

What happens if the main battery gets connected backwards?

2008 Mitsubishi Nativa (Pajero?) now no power coming from alternator after my experienced mechanic hooked up the car's battery backwards. He saw the spark he said but didn't register as he was ...
captcorvette's user avatar
0 votes
0 answers
44 views

Car only starts sometimes

My 2003 V6 Mitsubishi VRX Series 2 Diamante Has an issue where sometimes it starts fine and other times it will crank but wont catch, it’ll just sit there making a “nenenene” noise like its waiting to ...
User 43's user avatar
0 votes
1 answer
76 views

Turboing a 4B11

I own a 2015 base model lancer with the 4b11 and I want to turbo it so I’m going to get another 4b11 and put all my mods on it and when it’s done pull my stock engine and put the built one in my ...
Chris's user avatar
  • 1
0 votes
1 answer
210 views

My 2005 Mitsubishi Outlander is spitting coolant out the overflow tank at the top and causing my car to overheat

My 2005 Mitsubishi Outlander is spitting out coolant at the top of my overflow tank don’t know why. replaced the water pump because it had a slight leak checked the thermostat it worked just fine. Did ...
Austin Graszer's user avatar
2 votes
0 answers
33 views

Fuel gauge query

we have a pretty old Mitsubishi Galant and live in Thailand. I am curious as to why the fuel gauge registers quicker depending on the brand of fuel;for example when we refill at a Shell pump the gauge ...
Jessica's user avatar
  • 21
3 votes
1 answer
126 views

Hit a deer and piece to headlight snapped

Okay so I hit a deer. There’s actually not too much damage except for some dents and this plastic part that snapped. The headlight moves Around now so I know I have to replace it but I don’t know what ...
Bun's user avatar
  • 31
0 votes
1 answer
149 views

Grinding noise from brakes

Lancer 2005 es non-abs I have this problem of brakes grinding from the driver side wheel. All parts are new. Wheel bearing, brake pad clips. Brake pad, rotor, tyres. Still grinding noise. The noise ...
binu samuel's user avatar
1 vote
2 answers
551 views

Is this too much rust to repair?

I (maybe foolishly), recently purchased this car privately. I failed to inspect the underbody of the vehicle accurately. It's a 2011 Mitsubishi Lancer. I was wondering is this rust too much to get ...
Matt's user avatar
  • 11
0 votes
1 answer
170 views

Mitsubishi Super Shift transmission Power vs Economy

I recently bought a Mitsubishi Tredia 1985, but I've no idea on its super shift transmission gearbox. I can see there are two modes in super shifting gear as star icon (power) and E letter for the ...
Googlian's user avatar
  • 101
2 votes
1 answer
361 views

What are the definitions for the Outlander PHEV Routine Maintenance schedules?

I have a 2019 Mitsubishi Outlander PHEV. It's possible to change the "Routine Maintenance" window on the vehicle to numerous settings. However, they have not so descriptive names like "Normal", "...
Deleted User's user avatar
2 votes
1 answer
463 views

Mitsubishi Canter will not go into 4th gear

2013 Mitsubishi Canter 6500kg GVM 5 speed tip truck. Recently had a new clutch installed. Drives fine until the engine warms up. Then will not go into 4th gear. All other gears work fine.
Freddy GAGA's user avatar
0 votes
3 answers
74 views

New replacement rear shocks/strut replacement cartridges are not available, can I have them rebuilt?

1986 Mitsubishi Starion ESI-R Turbo
Mark's user avatar
  • 1
0 votes
0 answers
22 views

97' lancer hestitates under acceleration

I have a 97' lancer with the 1.6 engine, here's the thing, when I press the accelerator slightly it jerks a little no matter if Im moving, or taking off from a stop, If I press it more, like doing a ...
BryanPV's user avatar
  • 21
1 vote
1 answer
4k views

OBD2 Scanner can not detect ECU 2002 Mitsubishi Lancer

I bought a OBD2 Bluetooth scanner online. However, when I connect it to the OBD2 port in the car, the app while connecting to the OBD2 scanner gives an error message that it cannot connect to the cars ...
Michael Schroter's user avatar
1 vote
0 answers
73 views

mitsubishi pajero 3.5L petrol 2002 model

Pajero was running rough so I had the plugs and cables changed no difference, so had the fuel injectors changed and a new gasket, seems to be sucking air somewhere drives ok but coughs and splutters ...
David Smith's user avatar
1 vote
1 answer
94 views

Mitsubishi Lancer chugging

So I have a 2016 lancer, it has about 65000 miles on it. I got it used and now it’s making a rattling sound as well as when my wife and I are driving it it will sometimes chug and blow some white or ...
Fleury's user avatar
  • 11
2 votes
2 answers
46 views

Reusing head gasket for 1985 mitsibushi pajero

Recently i have repair my Mitsubishi pajero engine and used it for almost not more than 8days. Unfortunately the crankshaft broke on the way i was driving 100km far from my home. Now i bought new ...
Seyoum Shewayrga's user avatar
0 votes
4 answers
566 views

Timing Belt Broke

Is a 2003 Mitsubishi Galant engine an interference or non-interference engine? My son drove the car at about 40 MPH and the timing belt broke. I am trying to decide whether to scrap her or not.
ROBERT's user avatar
  • 1
1 vote
0 answers
152 views

2017 CF MY17 Black Edition - "Routine Maintenance Required"

My 2017 Black Edition Lancer shows this alert every time I start the car. It's been doing this for a few days now. The service sticker says next service at 17,000km; I'm only halfway there. What ...
user9506231's user avatar
5 votes
3 answers
919 views

faulty alternator problem?

I have a 2002 mitsubishi magna, battery light came on intermittently one day and a few months later the car died mid drive, battery completely dead. i got a jump start which lasted about a minute ...
Royce's user avatar
  • 51
0 votes
1 answer
2k views

Mitsubishi Lancer 2017 AUX input

I have a 2017 Mitsubishi Lancer Black Edition CF Auto MY17. As shown below, the factory (stock) head unit has an AUX option, but there is no 3.5mm AUX input anywhere in the car. The USB/iPod option ...
user9506231's user avatar