Questions tagged [manual-transmission]

A transmission that is controlled by the operator of the vehicle to select an operator desired gear.

68 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
4
votes
0answers
1k views

Clutch noise after changing gears

I own a Hyndai Elantra Coupe (2013 or 2014, can't remember), and for a time I was changing gears downwards in order to brake (the context is we were taught, in driving school, that you can do this if ...
4
votes
0answers
169 views

Gearbox Swap '93 model mitsubishi triton MJ

I bought two cars, one as a road vehicle and another as spares. They're both Mitsubishi Triton MJ. My road vehicle is a '93 model and the spare is a '94 model. My question is whether it's possible to ...
3
votes
0answers
151 views

Engine 'lugging' when turned off with clutch engaged, transmission in netural

After asking this question yesterday, I started thinking about how since picking up my second '06 Infiniti G35 Sedan in as many years, I've noticed that with this engine (145k miles), when I leave the ...
3
votes
0answers
7k views

Scania problem in engaging gears

I am having a problem in engaging gears on my truck series P124 R420. So I started by diagnosing and found no problem. Then removed the gearbox and changed clutch plate & pressure plate. Then ...
2
votes
1answer
93 views

Low clutch biting point

I have a 62 plate 1.2 Ford KA Zetec. I’ve had it about a year and have been having problems for about 6 months. If I am creeping forward in traffic for longer than five minutes, the bite starts to ...
2
votes
0answers
65 views

Difficultly in changing gears

I have ford fiesta. Car was in good condition. All of a sudden, I started facing a weird issue which my mechanic also facing tough time identifying the real problem. My car is running fine from the ...
2
votes
0answers
62 views

Won't go into gear (rare occasion)

I have a Nissan X-Trail T30. Recently, I noticed that the car won't go into gear from time to time. Most of the time, it drives just fine. It happens after driving quite a distance. I didn't notice ...
2
votes
1answer
118 views

Spinning clutch by hand with alignment tool?

I'm in the process of cobbling together a custom clutch fork/pivot/throwout bearing setup for a classic Chevy with a reproduction clutch, but I'm having difficulty measuring the clutch pressure plate ...
2
votes
0answers
33 views

Consistent white smoke from the exhaust

I'm driving a 2011 mini (175000) and it went for service and it was serviced by a BMW mechanic. After that there was consistent white smoke every time i drive off from the 1st gear. what might be the ...
2
votes
0answers
202 views

Grinding when pulling of in first gear, all other gears fine

I have a 2004 toyota yaris. I hear a grinding noise from by the clutch when pulling off in first gear. If I lift the clutch up really slowly it doesn't make the noise. I'm just wondering what could ...
2
votes
0answers
136 views

Stuck in first gear

I have a manual Toyota Camry . I find that I cannot get out of first gear when I go above 2000 rpm . It is stuck in first gear until I slow right down to 1000 revs . Then I can move into second gear. ...
2
votes
0answers
29 views

98 Mustang Randomly loses power w/ gas smell

So when I'm driving around, and specifically when it's humid as I've noticed, my car will randomly lose power and when at a constant speed, start lurching back and forth. Every time this happens, all ...
2
votes
0answers
33 views

VW stick shift shifter lockout

So my 2007 VW GTI has 257k miles.. (I know.) But it is my daily driver for now. I went on the highway and while I was in 6th, it popped into neutral by itself. I got kinda sketch but I was like okay ...
2
votes
0answers
265 views

91 Jeep YJ - Intermittent Loss of Power in Gear

The other morning, I pulled out of the house in first gear just fine. Switched to 2nd successfully, started accelerating as it should, then it suddenly lost engine power - no acceleration, no revving, ...
2
votes
2answers
4k views

Scania 4 series Opticruise gearbox problems

I am having issues with the Scanias. I have a 4 series Bus (K124) Opticruise. These are 8 speed 4 Low / 4 High Range. We are having an intermittent issue with banging into gear. This will only happen ...
2
votes
0answers
110 views

Manual Tranny jerkiness on and off throttle

2006 Mazda3 here. What is the expected smoothness in a manual transmission when letting on and off throttle. Here are my observatons. When releasing + pressing throttle car bounces/rocks forward like ...
2
votes
0answers
272 views

Reverse gear and marble noise

On my Mazda3 sometimes my gear shifter doesn't seem to throw all the way, and whenever I engage the clutch I hear what sounds like marbles. What could be the cause of this? I can put car in neutral ...
2
votes
0answers
50 views

1998 cherokee sport 4x4 hydraulic clutch problems

The clutch in my 19 98 Jeep Cherokee four by four feels like its frozen. The transmission will not go into any gear, including reverse. Whether the car is started, or not.
2
votes
0answers
481 views

Mystery-2008 Scion xB sticks in gear

So my wife has a 2008 Scion xB with a manual transmission. We've been having a problem that comes and goes with it, and is difficult to get to the bottom of. When we're driving the vehicle, it ...
2
votes
0answers
150 views

99 BMW 323i E46 5 Speed Manual Trans Stuck In Reverse

I drained the fluid and found metal pieces. It won't shift into any gear other than reverse. When I try to shift into the other gears it locks up and stalls out. Can anybody help I think I'll have to ...
1
vote
0answers
20 views

VW MQ200 Gear Selector Shaft Bolt/Nut is Snapped, does the whole gearbox need to be replaced?

The Gearbox is a Volkswagon MQ200 series installed on a Skoda Octavia 2008. I experienced problem with the reverse and 5th gear engagement, so attempted to fix the problem. While tightening the nut/...
1
vote
0answers
29 views

High pitched revving/sensitive gas pedal?

I live in the UK and went to go and test drive a 1.0L Peugeot 108. The car was in good condition and it's from a main dealer at a fair price which is why I am attracted to it. It was obviously sitting ...
1
vote
0answers
21 views

Gearbox vibrates vibrates on 1st gear and reverse

Opel astr g z18xe 2001.i have just changed my clutch plate only not the pressure and flywheel plate. Gear box vibrates when it is on 1st gear even on reverse. Why?
1
vote
0answers
38 views

Engaged handbrake & reversing

This morning I got into the car, applied the clutch, selected reverse, and heard a crunch sound. Now when I'm driving and I go to stop or slow down I hear this metal-on-metal grinding noise. Do you ...
1
vote
0answers
20 views

BMW manual transmission slow to accelerate but only in certain gears

After a service where the engine computer was replaced, I've noticed that certain gears are not behaving normally. 2nd, 4th and 6th behave normally: if I have my foot down on the gas pedal, it ...
1
vote
1answer
53 views

Clutch on new car

I recently bought a new Suzuki Dzire manual transmission and I have this weird behavior with the clutch’s biting point. When I start the car in the morning everything’s fine. The biting point is about ...
1
vote
0answers
12 views

opel corsa 2010 manual transmission abs acceleration

hi there does any one have info, I have a opel corsa 2010 manual transmission, when changing gears 4 to 5 in neutral time engine rpm goes to maximum without pressing gas pedal, no faulty codes stored,...
1
vote
1answer
1k views

4.3/350 Chevy flywheel interchangeable?

I have a 1997 S10 I'm thinking of doing a V8 swap with in the future does anyone know if the flywheel off of a 4.3 Chevy would work on a older 350 Since they’re basically identical minus 2 cylinders ...
1
vote
0answers
46 views

Big clunk/thunk when stopping fully

This problem started about a month ago. Just got back from traveling for the holidays and have to resolve this problem ASAP. Sometimes, but not always, the truck will clunk or thud hard when going ...
1
vote
0answers
78 views

Clutch engages lower after mechanic repaired slave cylinder. Can I adjust this to what it was?

Disclaimer: I have a very basic understanding of clutch and master/slave cylinder. (i.e. I know it's a basic hydraulic system) Car: 2000 Hyundai accent A year ago, I had my car towed in when it was ...
1
vote
0answers
99 views

Golf 5 stuck when shifting between 2 and 3 gear

While driving in 2nd gear, clutch down, try to go into 3rd (this happens like once in 30) the joystick kinda get stuck in the middle, like mid-way into the downwards 'state' as I would if I wanted to ...
1
vote
0answers
41 views

gearbox or just bearing

Hi All before going ahead and buying another gear box and clutch kit some advice may help. I have a mk7 ford transit with a 6 speed box I had never had a problem with getting into gear But had a ...
1
vote
1answer
34 views

2002 Ford Ranger. W/ transmission issue

I have a standard Ford Ranger that shimmies when I take off in first real bad so I take off and 2nd and it shimmies less please help
1
vote
0answers
102 views

2005 Suzuki gsxr 750

I just bought a 05 gsxr750 it has 6k miles on it. I recently did a fresh oil change new air filter new spark plugs and tightened up the chain and lubed. I have had no problems running it until last ...
1
vote
0answers
74 views

I have engine revs problems with my 1999 Grand Vitara 2.5 L manual

I have a manual transmission and when I pressed acceleration the RPM goes up but it takes awhile for it to drop back down until I shift what is the problem
1
vote
0answers
4k views

Mitsubishi truck Stuck in gear - manual transmission, shifter moves

Anyone has suggestions for what to check when a manual transmission won’t shift out of gear? It’s a 1984 Mitsubishi turbo diesel truck with 5 speed manual transmission. When the clutch is released ...
1
vote
0answers
33 views

2003 Nissan Maxima vibrating

[My 2003 Nissan Maxima, with standard transmission, is vibrating a lot.] I have changed the motor mounts, ignition coil packs, clutch, and my car still vibrates. A lot. Does anyone know what the ...
1
vote
0answers
104 views

Why won't my Mustang move in 1st, 2nd, 3rd gear after clutch change?

My mustang will not move in first or second or 3rd gear but will in 4th gear. I really need some advice regarding the issue. It is rattling when the pedal isn't engaged. I recently paid for a new ...
1
vote
0answers
712 views

Whining Engine Noise Nissan Qashqai

Vehicle: 2013 Nissan Qashqai Yesterday driving my Qashqai was a weird experience. The car starts jerking (as if it were on a hill with low speed/incorrect gear) on the 2nd gear at 2500RPM. I usually ...
1
vote
0answers
31 views

1998 Pontaic Firebird Base, what is causing a strange sound in 4th and 5th gears?

I have a 1998 Firebird, base model with a 3.8L v6 engine with a 5 speed manual transmission. When I am driving faster than 50 mph in 4th, or 5th gear, I hear a hissing/humming sound from the direction ...
1
vote
0answers
49 views

1.5l Mitsubishi mirage manual clutch kit install…already have bell housing back on…can't remember how the routing went of components

You already know what type of vehicle and that this issue has to do with wiring and brackets and components placement. What I need is a view or summary with relative description as to where everything ...
1
vote
0answers
97 views

Where to learn about manual transmissions?

I own a 2007 ford fiesta ST150, which is a 2L FWD, so obviously it has a transaxle. I'm generally pretty comfortable working with my car, I'm only an amateur, a shade tree mechanic but I'll happily ...
1
vote
0answers
451 views

Ford Ranger 3.0 TDCI XLT - Fifth Gear Problems

I have a Ford Ranger 3.0 TDCI XLT 2007 Model. I can get all my gears except fifth gear. I have checked the hydraulic clutch and bled it. Still the same problem. After driving with it, it also started ...
1
vote
0answers
2k views

Nissan xtrail T32 manual gear box/transmission issue?

I have a new Nissan xTrail petrol T32, and have noticed two issues. When I change from 1st to 2nd and from 2nd to 3rd especially, it does not go as smoothly and effortlessly as the other cars I have ...
1
vote
0answers
272 views

Clutch pedal is sticking and will not go down all the way on a 1994 nissan frontier truck

The clutch pedal on my 1994 Nissan Frontier will only go down about one quarter of the entire throw. I can put the shifter in gear but its like I still have the clutch pushed in. I can shift into any ...
1
vote
0answers
110 views

The car engages gears but does not move and when i depress the clutch it also sounds like grinding metal

Mazda rx8 , 2004 13b Manual Transmission 6 speed
1
vote
0answers
47 views

1991 Mazda Navajo clutch issue

I have a 1991 Mazda Navajo SUV I just purchased, it has a 5 speed manual transmission with 4wd but the 4wd to my knowledge does not work. I drove it around the first few days I had it and it drove ...
1
vote
0answers
240 views

2011 hyundai ix35 2.0 petrol trouble shifting from 1st to 2nd when its still cold

I have a 2011 hyundai ix35 2.0 petrol. When i start it in the morning it struggles to shift from 1st to 2nd and should you want to gear down from 3rd back to 2nd it is also very sticky. Clutch kit has ...
0
votes
0answers
38 views

Hissing noise when clutch pressed [SUBARU WRX, manual]

Recently I started to notice right after cold start there is a hissing noise coming from the bottom of the car on the driver's side when clutch is pressed. The noise usually goes away after driving ...
0
votes
0answers
32 views

Vehicle is not responding properly in 1st gear, Sometimes

Bought Ford Freestyle Titanium Plus (Petrol) 4 months before. Sometimes, In 1st gear, the vehicle is not responding properly for the throttle. All I am seeing is, the RPM stays <= 1K or <=1.5K ...