Questions tagged [manual-transmission]

A transmission that is controlled by the operator of the vehicle to select an operator desired gear.

Filter by
Sorted by
Tagged with
1
vote
1answer
32 views

Car jerks when dis-engaging clutch quickly

1988 Accord, 5 speed manual. If I disengage the clucth quickly the car feels like it jerks. There are no other problems with engaging the clutch or changing gears. Engine mounts appear ok - I can't ...
1
vote
0answers
27 views

New Clutch Fit 7,000 Miles Ago Clutch Feels Light Again?

Nissan Almera N16. My clutch was slipping in nearly all gears when under load, the clutch pedal itself was always heavy under my ownership. Had a new clutch fit on 07/04/20 (7,000 miles ago). The ...
1
vote
2answers
37 views

What else should I check and/or repair when replacing the clutch?

Based on a recent question I asked, I'm looking to have a shop replace the clutch in my 2008 Mazda 3i manual transmission with ~130000 miles on it. Before I do, is there anything else I should / could ...
1
vote
0answers
45 views

What's this part called? (a manual transmission shifting mechanism connecting to the shifter under the hood. 2000 hyundai accent)

Close up of it. Zoomed out, to show it's relative location. Awhile back, I was trying to see what I could do to improve the feel of the shifter, and decided to proactively replace the gear oil and ...
1
vote
1answer
39 views

2002 Ford Ranger transmission issue

I have a standard Ford Ranger that shimmies when I take off in first real bad so I take off and 2nd and it shimmies less please help
0
votes
2answers
71 views

Did I hose my transmission?

I have a 2013 Ford Mustang with an MT82 6-speed manual transmission. I don't know the history of the car so I figured it would be a good idea to change the transmission fluid. I drained it out and ...
0
votes
0answers
11 views

Car stalls couple times after start-up

I own a 2004 mitsubishi lancer, everytime i start driving the car for the day it always stalls when coming to a stop even if the car is in neutral. After driving for about 5 minutes, it no longer ...
1
vote
1answer
28 views

Stuck Clutch 1995 Alfa Romeo 916 S 2.0 l TS

I bought a Alfa Romeo 916 and knew I would have to do some work on it, including replacing the clutch. I bought a LuK clutch and replaced the clutch plate, pressure plate, and throwout bearing (...
2
votes
1answer
39 views

What caused my manual transmission to rev while shifting gears and now won't go at all?

I have a 2008 Mazda 3i Touring (2.0L engine) with a manual transmission, ~130k miles on it. For a few weeks, whenever I shifted gears the engine would rev (up to 3000-4000 rpm) for a second or two ...
-1
votes
1answer
63 views

Can you shift to neutral while full acceleration in a manual transmission, without using the clutch?

It's a pure theoretical question and these are the conditions: car is at the highest torque while accelerating (5000rpm gasoline or 3500rpm diesel) car is in 2nd gear (still has force to accelerate ...
2
votes
1answer
159 views

Spinning clutch by hand with alignment tool?

I'm in the process of cobbling together a custom clutch fork/pivot/throwout bearing setup for a classic Chevy with a reproduction clutch, but I'm having difficulty measuring the clutch pressure plate ...
0
votes
1answer
58 views

Dodge Dakota 2001 gets stuck in first or reverse gear, then stalls

But it only seems to happen when I'm in a situation where I have to be on the clutch for longer than usual, like in a parking lot. This never happens when I'm driving anywhere or at a stop light. ...
1
vote
1answer
73 views

Clutch on new car

I recently bought a new Suzuki Dzire manual transmission and I have this weird behavior with the clutch’s biting point. When I start the car in the morning everything’s fine. The biting point is about ...
0
votes
0answers
56 views

Car vibration in 1st gear and no throttle (when moving in traffic jams)

I have a VAG 1.6TDI 5spd MT octavia. I've often noticed that there is a lot of vibration when moving in 1st gear whenno throttle is added (as in traffic jams or whenever traffic moves really slow). ...
0
votes
4answers
6k views

Air,in my clutch system

I went through all the procedures of bleeding my clutch and slave cyclender and still no clutch pedal at all and everything is all new is there something I'm missing can u please let me know thank u ...
1
vote
1answer
2k views

4.3/350 Chevy flywheel interchangeable?

I have a 1997 S10 I'm thinking of doing a V8 swap with in the future does anyone know if the flywheel off of a 4.3 Chevy would work on a older 350 Since they’re basically identical minus 2 cylinders ...
1
vote
0answers
51 views

When replacing parts in a manual gearbox, do mating parts need to be changed together?

I'm trying to diagnose a notchy/difficult shifting condition for a 1-2 and 2-3 shift. This is a M5R1 / M5OD (Toyo/Kogyo) transmission that was recently rebuilt (by me). Vehicle is a 1998 Ford Explorer....
1
vote
2answers
41 views

Grinding when Shifting to First Gear - 2005 VW Jetta 2.5L (5-speed manual)

I have a 2005 VW Jetta 2.5L (MK5, 5-speed manual) and the clutch grinds when I shift into first if I don't depress the clutch pedal for about a second or two first. One thing to note is that before I ...
3
votes
0answers
8k views

Scania problem in engaging gears

I am having a problem in engaging gears on my truck series P124 R420. So I started by diagnosing and found no problem. Then removed the gearbox and changed clutch plate & pressure plate. Then ...
2
votes
2answers
5k views

Scania 4 series Opticruise gearbox problems

I am having issues with the Scanias. I have a 4 series Bus (K124) Opticruise. These are 8 speed 4 Low / 4 High Range. We are having an intermittent issue with banging into gear. This will only happen ...
2
votes
1answer
426 views

Low clutch biting point

I have a 62 plate 1.2 Ford KA Zetec. I’ve had it about a year and have been having problems for about 6 months. If I am creeping forward in traffic for longer than five minutes, the bite starts to ...
1
vote
2answers
45k views

Burning smell after stalling in hill start

I am driving a manual car and I usually have no issues with hill starts. Today, however, after pulling my e-brake on on a hill and then engaging 1st gear. My car would not pull forward from ...
0
votes
1answer
75 views

2019 manual transmission Subaru Imprezza skips lacks in acceleration

I drive a new 2019 manual transmission Subaru Imprezza. Started driving her five months ago. She's only had one oil change. Synthetic oil before and after the oil change. She's been stalled less than ...
0
votes
1answer
210 views

Clutch pedal sticks in semi-released position, then snaps rest of way — worn disk? Something else?

Recently, I was trying to climb a slick frosted country road (near my home), and had to ride the clutch quite a bit to do it. At one point, I got stuck in a snowdrift so that the car wasn't moving at ...
5
votes
3answers
2k views

2000 Honda Accord Shakes under acceleration

I have have Honda Accord 2000 with manual 5 gear transmission. During acceleration it shakes like front end is ready to jump out. Engine doesn't misfire or anything - I have plenty of power on all ...
0
votes
0answers
32 views

What can be faulty on my clutch system ? Mustang '67

I've ran out of ideas, haven't had the time to go under the car so I would like to know your opinion. I was riding my '67 Mustang, until gears suddenly felt stiff to engage, afterwards I realized the ...
0
votes
1answer
68 views

Would cold temperatures affect a neutral safety switch? (Manual transmission)

Trying to troubleshoot my 92 Subaru Legacy manual transmission starting issues. Car wont crank/start most mornings, even if its only about 50 degrees F. Replaced battery, starter, and alternator ...
8
votes
4answers
3k views

How to keep a car with manual transmission from rolling downhill when parking on a sloped surface? [closed]

(updated the change the term "sliding" to the, in this case, more correct "rolling") About parking a car with a manual transmission on a sloped surface: Is it normal that the car starts rolling ...
1
vote
0answers
39 views

VW MQ200 Gear Selector Shaft Bolt/Nut is Snapped, does the whole gearbox need to be replaced?

The Gearbox is a Volkswagon MQ200 series installed on a Skoda Octavia 2008. I experienced problem with the reverse and 5th gear engagement, so attempted to fix the problem. While tightening the nut/...
0
votes
0answers
45 views

Hissing noise when clutch pressed [SUBARU WRX, manual]

Recently I started to notice right after cold start there is a hissing noise coming from the bottom of the car on the driver's side when clutch is pressed. The noise usually goes away after driving ...
2
votes
2answers
99 views

05 WRX drive train issue,grinding noise coming from center to back of car + rear wheel hop developping during tight slow turns

I have a 05 WRX which has been producing grinding noise from somewhere between the center to the back of the car. The noise starts to happen once the car is warmed up and under power. It can also keep ...
4
votes
2answers
467 views

Vibration during Deceleration

I have a 2001 Mitsubishi Lancer CE, I recently replaced the clutch as the release bearing was no longer servicable. After replacing the clutch I noticed during deceleration a vibration like noise. At ...
5
votes
4answers
7k views

Will a manual vehicle stall at low RPM without being on the accelerator?

Say you're in third gear going in a straight line with no need to stop. You let off the accelerator and downshift to second gear then coast with no pedals in use. Will the car reach a certain RPM and ...
0
votes
0answers
34 views

Vehicle is not responding properly in 1st gear, Sometimes

Bought Ford Freestyle Titanium Plus (Petrol) 4 months before. Sometimes, In 1st gear, the vehicle is not responding properly for the throttle. All I am seeing is, the RPM stays <= 1K or <=1.5K ...
0
votes
0answers
16 views

2006 Xterra with Toyota Engine

I have blown my Xterra engine twice and the cost of finding a good replacement is sky high. I managed to get used LS430 3UZFE used engine into the bay. Its a V8. We mated the Toyota computer to the ...
0
votes
0answers
48 views

Manual transmission lugging in first gear

I drive a 2006 Subaru Legacy Wagon with a 5-speed manual transmission. When I've been driving it recently I have had more trouble then I remember starting it on an uphill. When I use the same power ...
0
votes
0answers
52 views

Manual Honda Civic 2019. Rarely from a stop my stick won't shift into the first gear

So I've driven manual my entire life, but this is my first new car. I notice that the stick moving into the various gears is not a smooth experience and occasionally from stopped position pushing the ...
1
vote
2answers
43 views

Freshly Rebuilt EJ25D makes horrid 50+ decible squealing with belts on

I have a 98 Legacy Outback that squeals really badly when it gets started. any combination of belts doesn't fix the issue and i changed the alternator and the power steering pump has been tested on a ...
8
votes
3answers
1k views

Why can't the 3rd generation Mazda rx7 safely coast downhill in neutral?

The manual for the 3rd generation Mazda rx7 says not to roll downhill without the engine engaged, because the exhaust can overheat. Unfortunately, the manual does not explain the mechanism by which ...
1
vote
2answers
79 views

Can forcing into gear with the engine off cause damage to the pressure friction plate, flywheel or cause the clutch to burn out?

In November 2019 a new drive train was fitted. I was not advised that a new clutch was needed. The car is 4 years old and has done 87000. Just over a week ago I broke down. I couldn't get the car ...
1
vote
1answer
100 views

Won’t start with touching starter solenoid with screwdriver and it turns off my speedometer and glitches out!

I’ve been having problems with my 09 Kawasaki Ex250R. Every time I go to click ignition switch I hear a click in the electrical relay near battery. It might be that but I also tried bypassing the ...
2
votes
1answer
107 views

Transmission is slow to engage

I have a 1988 GMC Sierra 4x4 truck, and I recently bought a rebuilt NV3500 transmission from a 1995 chevy truck (I picked this year, because from 1993 onward, this particular transmission used a ...
1
vote
0answers
35 views

High pitched revving/sensitive gas pedal?

I live in the UK and went to go and test drive a 1.0L Peugeot 108. The car was in good condition and it's from a main dealer at a fair price which is why I am attracted to it. It was obviously sitting ...
3
votes
1answer
100 views

What is the name of this?

My car is hard to shift gears and found out this was the reason. Any idea what’s the name of this part?
1
vote
0answers
21 views

Gearbox vibrates vibrates on 1st gear and reverse

Opel astr g z18xe 2001.i have just changed my clutch plate only not the pressure and flywheel plate. Gear box vibrates when it is on 1st gear even on reverse. Why?
2
votes
2answers
668 views

Possible Causes of an Engine Tick?

I own a 1999 Mercury Cougar, running the 2.5L Duratech DOHC V6. I was recently out with a friend drifting (not the smartest idea, especially since my engine was already running rough), and while ...
7
votes
4answers
30k views

Manual transmission difficult to put into gear. Do I need a new clutch?

I have a 1998 Jeep Cherokee Sport, manual transmission (the 6 cylinder model, I believe 4.0L). It has 4 wheel drive. I've lent the car to some friends recently who were 'rusty' with their manual ...
1
vote
1answer
61 views

Does anyone know the name of this part?

My Vw Jetta 2005 (manual transmission) is having a hard time switching gears. Found out this was the problem. Does anyone know the name of this? (https://i.stack.imgur.com/JrgMR.jpg)
0
votes
0answers
46 views

Revving up engine gives more power to steering

I'm from India and I drive a manual Petrol Maruti Suzuki Baleno. The car handles kind of well and it's been only since I have bought it and has driven for around 10,000 km. Yesterday, I accidentally ...
0
votes
1answer
98 views

Why can I disengage transmission without clutch pedal only when decelerating?

Something strange that I noticed on my manual transmission car (Renault Clio 3). Any gear can be smoothly disengaged without use of the clutch pedal, but only when the car is decelerating (ie. when ...

1
2 3 4 5
9