Questions tagged [atv]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
0answers
29 views

ATV need advice on fixing flat tires

I bought a cheap Chinese ATV thats probably 30-40 yrs old, and it runs great and is lots of fun, but shortly after I bought it 2 tires went flat and wont hold air. I live in MD and theres very few ...
0
votes
1answer
37 views

spark plug gap gets smaller

so im trying to get my atv running and i took out the spark plug and realized that the center electrode and ground electrode was touching no gap at all so i pulled them apart and put it back in tried ...
1
vote
1answer
32 views

What part could I use for this battery terminal?

This Suzuki ATV battery requires a special kind of right angle terminal attached to the battery. Items 2 and 3 in the figure: Here's a close up of what one looks like: I don't have the terminals ...
1
vote
1answer
58 views

ATV starter motor: replace or rebuild?

I've got an OEM Suzuki ATV LT160 starter motor that's not functioning. I've seen replacement motors and rebuild kits. When is it appropriate to try to rebuild a starter motor vs replacing it?
1
vote
0answers
36 views

Can you use a flex (spider) coupler as a dog clutch in a motorbike/atv/go kart/lawn mower like setting?

My question is simple: I want to make a dog clutch system for a wakeboarding cable system and was wondering if a flex (spider) coupler could used? The power, velocity, torque is similar to a go kart /...
0
votes
1answer
35 views

Suzuki ATV LT160 wheel hub gets stuck going on

I've got a 2000 Suzuki LT160 ATV. The bearings blew up inside the wheel hub while riding. I took the entire front right wheel assembly off, including the knuckle arm and cleaned everything. Had to ...
0
votes
0answers
146 views

Where to hook up my carburetor hoses on a 1998 Yamaha Breeze

1998 Yamaha breeze Four wheeler. Where do the carburetor hoses hook up
3
votes
1answer
181 views

2014 TGB 550I LT 4x4 stutters after sharp turn (right)

We have an ATV and we just got it up and running again (got scammed when we bought it). The ATV had been standing still for a few years. The ATV had a damaged front wheel and because of a bad repair ...
2
votes
0answers
718 views

Honda ATV TRX350 4x4 '89engine remove, how to disconnect from drive shafts?

I bought an 1989 Honda TR350 4x4 with possibly a blown rod bearing/scratched piston. The quad itself http://i.imgur.com/p0Bd1hA.jpg I'm trying to remove the engine, I have almost everything ...
5
votes
2answers
11k views

No compression on my two stroke

I was recently riding racing my Honda 250R (1986) (informally), and, all of a sudden, the engine quit completely. I tried letting out the clutch in second gear (push starting) with my momentum, but ...
0
votes
1answer
579 views

My motor in my 2003 Honda 400EX Four Wheeler is making a ticking noise

It's not the lifters might be timing chain but don't know.
-2
votes
1answer
286 views

Razor Dirt Quad kids ATV payload limit [closed]

What is the maximum "payload" (read: the weight the atv can carry besides itself) of the Razor Dirt Quad kids ATV? The specs say product weight is 89 lbs and something called "Max" is 120 lbs. The ...
5
votes
1answer
1k views

1985 Suzuki lt185 cap starter problem

I recently purchased a 1985 suzuki lt185, the guy said it needs new recoil starter, and I bought a 86 recoil starter (all the other recoil starters I came across said fit 1984-1987 I went to go put it ...
3
votes
2answers
2k views

How do you remove a stubbornly stuck rear hub on a 1993 Honda fourtrax 300?

I have a Honda Fourtrax and I have tried numerous things to get this stubborn hub off the rear axle it just won't budge I am open to any idea short of a stick of dynamite.
1
vote
1answer
1k views

ATV engine does not start well

I have a chinese ATV with an engine copied from an ~2006 Honda Foreman 400 (a very simple 1 cylinder 400cc carburetor based engine). It's an exact copy with regards to parts. However it does not start ...
4
votes
2answers
5k views

What damages may I have caused draining oil by filter?

My ATV oil drain plug is an allen 6mm bolt. The bolt was all rusty, and what I expected to happen happened - I stripped it. Instead of wasting times trying to remove the stripped bolt I drained oil ...