I have managed to completely fry the regulator/rectifier on my Suzuki GSXR600 (K7).

I suspect that it happened when I blindly splashed into a big water pond, some water probably got on the connector. But it is not really possible to avoid that as I use my motorcycle to commute every single day, rain or shine.

I have heard that GSXR's have this issue all the time.

  1. How do you look after your regulator/rectifier?
  2. Do you unplug it and let it vent every couple of months?
  3. Do you add some additional protection?

2 Answers 2


The regulator or rectifier isn't going to be bothered by a bit of water splashing on it. Quite simply, the voltage is too low for the water to pass a current. What is more likely is that water getting into/onto the high voltage part of the ignition circuit has caused a spike or surge to be sent through the low voltage circuit, which will fry rectifiers and other solid state components.

With that in mind, check to see that the ignition circuitry is well protected from the elements. If you can find it locally, get a can of silicone water shield and give your system a couple of coats of that.

If you can't do that you can always resort to what we did "in the old days", which is to wrap as much of the ignition stuff as possible in plastic. Just ensure you leave downward facing drainage points.

  • I haven't thought about the ignition part of the electrical system. Will have a look into it as it is easily approachable. Thanks.
    – Audrius
    Commented Mar 8, 2011 at 12:28

Not Necessarily an Issue

There is not a guarantee that there is a problem with your charging system if the rectifier on your 1999 Suzuki GSXR keeps burning out. Splashing through water is very unlikely to have been the root cause of the issue.

Suzuki Rectifiers

Your era of Suzuki is unfortunately notorious for burned out rectifiers and stators. Whomever they were sourcing them through had a huge quality control issue. The TLR and TLS of that era had the same issue as did many other models. Essentially, the charging systems were junk.

Testing Your Stator

There are three yellow wires that come from your stator. They come out of the left side crankshaft cover and route into your sprocket cover and out along the cast bottom portion of your frame on their way to your rectifier. They connect directly to the rectifier. You can disconnect them from the rectifier and test them with a multimeter. Your first test will be static. The engine is not running. Be sure to disconnect from the rectifier and not just try and pierce the wires with the multimeter end. They are special wires and insulated a bit more, these are one of the few wires on the motorcycle that carry AC current.

  • Static Test Set multimeter to ohms and test between all the leads in pairs. The reading 0.1 to 1.0 max resistance.

  • No Load Test Dynamic Test Set your multimeter to AC Volts and start the bike. It should be cold. Have a friend hold the RPM's at 5,000. Test between the leads. You should see more than 70V. If it's below that, you may need a new stator. I would replace, but I'll get to that later.

Testing Your Rectifier

Your rectifier has diodes in it. Diodes are one way valves for electricity, think of a reed valve in a two stroke in-take. Since this is a three-phase charging system you need diodes to join the AC current into a single output and convert to DC. I could get more detailed but I want to keep it simple.

  • Rectifier Resistance Test Using your multimeter set to ohms connect the multimeter to the ends of each of the diodes and check the resistance in both directions. You should have low resistance in one direction and higher in the opposite direction. Generally, you will want to see 5 - 40 ohms of resistance in the forward bias direction, and infinite resistance in the reverse bias direction.

  • Procedure Attach the black probe (-) of the meter to the ground side of the rectifier (black wires) and the red probe of the meter to each of the three contacts for the stator. Record the numbers. Then swap around the meter leads (red and black are swapped) and take the readings again. You have thus measured the ground side of the rectifier.

If you have lower resistance in both directions (5+ ohms) then it's shot. If you have infinite in both directions, then it's shot. Throw it away.


Do not buy a Suzuki rectifier. I have purchased my replacement rectifiers off Ebay fro the last six or seven years and haven't had an issue with any of them. I've purchased them all from domestic suppliers that make them for a plethora of motorcycles, ATV's and dirtbikes. You will find them by searching. I have only purchased domestic. These rectifiers have not given me a bit of issue. I have one on my son's track bike (2005 GSXR 600) since 2008 and that thing get's beat hard in the summer from 7000 RPM to redline over and over all day. The cost is about 20% cheaper than OEM from Suzuki.

Hope this was helpful


You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .