3

Whenever I drive over speed bumps (or pot holes or whathaveyou) I notice that when the rear wheels go over, the whole car jumps up and down and clatters, a lot more so than the front wheels. I am pretty sure the shocks are not the issue here, partly because I've changed them and the behavior didn't go away and partly because the problem is not that the back is too bouncy, it's that it's too stiff. It almost seems like there's something wrong with the coil springs, but they look fine and I have no idea how to test them otherwise... Any ideas?

The car is an Acura Integra from '93, a sporty hatchback.

3
  • what type of vehicle? most likely this is not something "wrong" with the vehicle, merely a consequence of suspension design, weight distribution, and physics.
    – mac
    Commented Oct 30, 2013 at 20:46
  • @mac it might well be that there's nothing wrong, but how do I determine if that's the case or not?
    – vlsd
    Commented Oct 30, 2013 at 21:01
  • Nice car.. :-).
    – Shobin P
    Commented May 20, 2015 at 6:09

3 Answers 3

7

A fairly common issue on cars with strut suspension are broken springs. As the strut wears it looses its ability to control spring dampening. This allows the spring to compress and expand faster and farther than designed. Over time the spring weakens and breaks. The break many times occurs at the very last turns of the spring and may go unnoticed. Look at the very bottom of the spring and see if the end appears as a clean edge or a jagged break. You should have the same number of coils on both sides. The shortened spring acts stiffer than the stock spring resulting in a harsher ride. Another source of banging maybe worn or damaged strut mounts ( in your case this should have been detected during replacement). You may also have worn suspension bushings that are allowing extra movement resulting in the banging. Don't forget to rule out a broken exhaust hanger letting the exhaust bang on the floor.

5
  • 2
    Mike nailed it: I would assume that any bushing or other rubber-based component on a 93 car is completely worn out. This includes the top mounts for the shocks, the bushing on the sway bars end links, the control arms, the exhaust hangers, etc. It's likely that if you crawl around under the car, you'll see a lot of worn out rubber bits.
    – Bob Cross
    Commented Oct 31, 2013 at 11:59
  • I've changed a few bushings already while doing the shocks. Replacing all of them is, while feasible, a serious and expensive undertaking. Is there any way to prioritize?
    – vlsd
    Commented Oct 31, 2013 at 17:27
  • 2
    @vlsd depending on the bushing geometry, you may be able to put some load on the joint with a prybar or something and observe the way the bushing reacts. You may be able to tell which are most worn in this way.
    – mac
    Commented Nov 1, 2013 at 14:28
  • Best answer..+1
    – Shobin P
    Commented May 20, 2015 at 6:09
  • I generally replace bushings with struts or shocks. For my VWs it adds about $12 per wheel.
    – mongo
    Commented Jun 2, 2017 at 20:26
1

Other suspension parts have bushings like a trailing arm on the rear. Suggest that you take a look at the function of the wheels using a second jack on the suspension when tge body is jacked and backed up with stands. Suspension bushings fail as well.

Also if you have any torsion bars check them as well.

One additional thought..around here many alignment shops and tire shops which do alignments, will do a courtesy check, where the lift the car up, and poke at the suspension with a pry bar. They don't charge. This gets experienced eyes on the suspension.

0

Its basic law of gravity here as for most of the cars engine are located at the front so they are heavier at the front so the front wheels remain calm and composed compared to rear of the car.You would experience the that your car would stop bouncing if you stuff your car's boot with luggage.

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .