1

For instance, an example catalogue extract for a motorcycle reads-

Bore / stroke : 102,5 mm x 76 mm. Capacity : 1,254 ccm. Rated output : 100 kW (136 PS) at 7,750 U/min. Max. torque : 143 Nm at 6,250 U/min. Compression ratio : 12,5 : 1.

From a user's point of view, surely they are more interested in how much forward thrust the vehicle can provide, as opposed to the torque at the rear wheel (which is also implementation dependent). Thrust is also more easily relatable to other parameters of interest, such as acceleration (assuming a known mass).

Perhaps there is an argument that thrust is dependent on further variables such as the effective rear wheel outer diameter (tyre pressure, tread etc.), road conditions (amount of slip), so only a reference figure can be given. However, I would argue back that torque by itself gives less information in terms of user experience.

From a quick check, aircraft engines are specified in terms of thrust, and not torque. So why not for bikes and cars? Interested to hear different points of view.

Example specs from BMW R1250GS product page- https://www.bmw-motorrad.co.uk/en/models/adventure/r1250gs/technicaldata.html#/section-technical-data

  • 1
    Because that is the engine power – Solar Mike Feb 13 at 10:34
  • 1
    Thrust is for rockets and jets. – Moab Feb 13 at 12:04
  • Piston aero engines are not specified in terms of thrust, but shaft horsepower (SHP) So are the jet engines used to drive propellers on turboprop output. In both cases the "thrust" depends on the design of the propeller, and also on the speed the plane is flying. – alephzero Feb 13 at 14:25
  • With an internal combustion engine the propelling force available at the wheel will vary with the gear selected. The quoted torque figure is at the crankshaft. The best use of performance figures is not as an absolute, but as a comparison with other engines / vehicles. – Weather Vane Feb 13 at 17:28
  • Thrust for a car is torque (at the crank) x gearing. Hence torque in first gear will be FAR higher than in top gear. The torque figures given for cars and bikes are not the torque at the wheels, rather the torque at the crank calculated from measuring at the wheels and calculating it back to the crank by taking the gearing into account. – Kickstart Feb 13 at 17:32
0

I'm not a 100% sure about the correctness of this answer, (please comment if you see errors)

First of all, the torque number specified, just says so much. The number is actually just the max value of a curve (because the torque is dependent of the engine speed). The torque curve is the interesting thing.

This means that if we compare two cars with the same weight, it's not certain that the one with highest max torque and max horse power will win in a dragrace. And even if the two cars had the exact same torque and hp numbers, it's still not certain that the one with the higher numbers would win. Because it's also dependent on the gearbox gearing and final gear (and wheel size).

The following picture shows a torque curve for a car, this curve also includes the gearbox!

https://cdn.shopify.com/s/files/1/0707/0667/files/RCTvSshiftpoint_large.jpg?5038209485651266688

The colors except the red shows the torque for each gear, and the red one just just the combination.

Now for the thrust. Implicitly the thrust curve is given by the torque curve combined with wheel size and final gearing. If you do some multiplications of these numbers you will (I think) get the thrust curve. As you can see the thrust curve will give you a peak in the low speeds (around 30-35 mph in this case). So now if you provide the thrust curve it says some about the acceleration, maybe more understandable than just the torque figure.

However you'd have to take into account the weight of the car, the wind- and rolling resistance etc. etc. to get a good view of the acceleration (which I assume is the interesting thing). And in that case, couldn't you just have a acceleration curve?

Also, it's more likely than not that the manufacturer would think it's simpler just to provide a number, and not the full curve. This would probably be the max number, and the question is how interesting the max thrust actually is since it only occurs once, and then drastically falls. So in that case isn't is just better with the 0-60 numbers as @Kitsunemimi says?

|improve this answer|||||
  • This answer does a good job of covering the "lot that can be said about this topic" that I didn't go into in my answer. Interestingly, if you take the "thrust curve" chart, and imagine the car had infinite gears (basically a CVT), and the torque curve accordingly plotted infinite times, then the entire curve can be described with a single number: peak horsepower. – Kitsunemimi Feb 13 at 14:58
0

There's a lot that can be said about this topic, but Solar Mike and Moab pretty much sum up the main reason for it. Torque isn't a metric that was derived for the purpose of describing "user experience", it's a measurement of the amount of force that an engine is capable of producing. Engines spin, therefore they produce torque. Rockets and jets push, therefore they produce thrust (generally). At the end of the day, it's just another number that describes the characteristics of a vehicle - as with many such numbers, you need to understand how to interpret it for it to be useful to you. The number you're probably more interested in is the 0-60 mph time.

|improve this answer|||||
0

I'll add a little to Kitsunemimi's answer (which is totally correct).

Simply, thrust is ONLY a linear force pointing in a single direction.

As stated, everything with ICEs ultimately is culminating in rotational energy (torque) which will lead to thrust (in a sense, but not really). Even where the rubber meets the road, we're not dealing with linear force, but rather many rotational forces that combine, moment after moment, to produce linear motion. (Note: a good way to see this is to observe a drag racing car's back wheels on launch in slow motion. Amazing.)

As you were noticing, all of the other factors of "user experience" are quite variable: road friction, tires, load weight, et al. The one constant that the manufacturer can sell to you is the stock engine output - independant of all these variables - which is just the torque output. Finally, as mentioned throughout, what ultimately determines the actual Nm/s² that the driver experiences will change dramatically depending on gear ratios, tire pressure, wheel size, and even the environmental factors like temp, humidity, pressure, etc.

Even with EVs, they still use torque and HP as ratings because the user can best infer what the experience could be like. They totally bypass the torque curve aspect of the equation, but it's still all about rotational force, rather than linear.

|improve this answer|||||

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.