I understand spring clamps are convenient to use on smaller hoses. However, my Tacoma came with them on even larger hoses, such as the radiator hoses, that are, I believe 1.25" and I can't seem to find a reason why there would use an easily mangled, hard to squeeze spring clamps when a regular strap clamp with a screw (AKA worm gear) would do just fine and would be a lot easier to use and put on.

BONUS: Someone told me that spring clamps are better because they apply pressure uniformly vs worm gear clamps that apply it in only one spot. While I am unable to scientifically disprove this, my gut feeling is that it is complete unfounded B.S. Can anyone offer a plausible explanation to dismiss this so I can go back to that person?

  • Do you mean 'worm' gear? – Glen Yates Dec 5 '17 at 17:28
  • yes, sorry. correction made – amphibient Dec 5 '17 at 17:32
  • The issue with a Worm Clamp is it can not passively adjust the way a constant-tension clamp does. This generally results in either leaks and/or breaking components. Plastic Water Necks specifically. – NitrusInc Apr 11 '18 at 15:15

Great question. Spring clamps have several advantages from the engineers point of view. They apply even pressure around the joint, screw clamps do not. Screw clamps pull from one side and this can stretch the hose, pulling it to the screw area. In smaller sizes, screw clamps leave a flat spot under the screw fitting; this leaves low pressure areas at the each end of the screw fitting. But most important spring clamps continue to apply pressure as the rubber of the hose dries out and shrinks over time making the joint last much longer without maintenance.

Corrosion can be in an issue for poorly coated spring clamps. Care must be taken to place a clamp back in the same place on an older hose. If not, it can leave a section with little or no pressure and lead to a leak. We switch back to spring clamps whenever we take a hose connection apart. We apply spray silicone lubricant between the clamp and the hose to allow it to slide as it shrinks.

This applies to flat band spring clamps, round wire clamps are a poor choice as they have too small of a pressure surface.

  • Although cost is certainly a factor for some manufacturers, as Fred pointed out there are also some advantages to the 'flat' spring clamps. One not mentioned here is vibration. A screw can 'back off' or loosen a bit after lots of vibration, whereas the spring style clamps do not. It's also worth mentioning that OEM clamps on many high-end cars such as Lamborghini's are spring style. I wouldn't expect they're doing this for 'cost cutting', but for the advantages listed above. – Nick G Sep 15 '15 at 15:37

The one simple reason manufacturers use spring clamps instead of worm gear clamps:


It costs far less to mass produce spring clamps and use them than it does worm gear clamps.

As far as your bonus question goes, I would agree with your gut. There is no way a spring clamp is going to clamp any better than a worm gear clamp. You would be able to get the worm gear clamp tighter than a spring clamp, that's for sure. As long as the worm gear clamp doesn't get deformed, you can continue applying force to it and getting it tighter. The spring clamp is still adequate for what it is designed to do, though, or it wouldn't still be in use today. The worm gear clamp would most likely last longer as long as it's made out of stainless steel (as opposed to the cheap aluminum ones I've seen from Harbor Freight). Realistically, though, either type of clamp should last for the life of the car.

  • 2
    You may want to edit this to state that cost is a major factor for manufacturers, but clearly there may also be some mechanical advantages to the spring style clamp as Fred Wilson pointed out. I don't think it's quite so black and white to state 'one simple reason' – Nick G Sep 15 '15 at 15:40

Spring style hose clamps are typically fabricated from steel alloy and plated with zinc for corrosion protection. Aluminum would not be a good choice for spring clamps due to low elastic limits and cost. Forming an aluminum spring would also require heat treat and tempering after forming then corrosion protection such as anodizing, all adding more cost. Steel Spring style hose clamps have several advantages over Worm Gear style clamps as they continuously apply the same clamping force under all environmental conditions, over their entire life. With temperatures changes, rubber shrinkage with age, and vibration loads, the spring style clamp consistently applies force to seal the hose. Worm Gear clamps on the other hand can become loose due to vibration, material shrinkage, temperature fluctuation and can be grossly over tightened damaging the hose and radiator fittings. Spring clamps are also much quicker and simpler to install. With the right tool the clamp is expanded and place into position and tightened by simply releasing the clamp. Worm Gear clamps require a way to rotate the worm gear numerous times to tighten and torque limiting method to prevent over tightening. For and assembly line, spring clamps make more sence.
I just replaced all of the hoses on a 22-year-old Honda that someone had put aftermarket hoses on and had to change to worm gear clamps because the hose diameter was larger than the OEM hose. The clamps were so tight that they cut the rubber to the fiber reinforcement layer, not good. Put OEM hoses and original spring clamps back on it, no leaks!

  • This is a great answer. +1 – NitrusInc Apr 11 '18 at 15:16

Regular strap clamps do not work as well. It's common to get cold-flow leakage around them whereas the spring clamps work better across the wide range of temperatures. If you have a strap clamp, you end up overtightening them to try and compensate.


Been researching this because i recently had an experience where the upper radiator hose came loose while i was driving and i was absolutely sure i had tightened down the the "worm gear" clamp properly when i installed the radiator. But apparently the rubber hose had compressed some and the clamp lost its clamping force. Being that the radiator inlet is plastic, I am somewhat worried about applying to much clamping force. I noticed that the original factory clamps were spring clamps. I see now that the advantage of the spring clamp is the constant clamping force even when the hose shrinks or compresses.


All makes sense to me. However, sometimes strang things occur. Hada 2007 avalon with power steering fluid leaking. Been leaking for years and owner was frequently topping it up with cheapo stp psf. Well i could see that the hoses were wet. I replaced all the wire spring clamps with worm roller and over tightened them im sure. Its been a year now and no more top ups. Every case is unique

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.