On-Board Diagnostics-II (OBD-II). Questions usually involve scan tools, their use and their compatibility, as well as how to interpret Diagnostic Trouble Codes (DTCs).

learn more… | top users | synonyms

4
votes
2answers
191 views

Calculating MPG from MAP sensor (or converting MAP data to MAF data)

My 2002 Honda Accord V6 has a Manifold Absolute Pressure sensor (MAP). I understand that this sensor gives out information in pressure units (psi or equivalent). After doing a bit of research, I ...
1
vote
1answer
71 views

Live scan tool for OBD 1.5 GM transitional?

1995 S-10 Blazer 4.3L Vortec V6 (vin W) with Powertrain Control Module (PCM) 1995 was the OBD transitional year for GM. The PCM itself is OBDI, but the interface connector has the 16-pin D-style ...
0
votes
1answer
35 views

Maruti Suzuki Swift Check Engine Light On And Engine Coolant Temperature Needle stay at 'C'

My Swift VXI has developed a condition. I have started to see the check-engine light on and the Engine Coolant Temperature Needle stays at 'C' after starting the engine. Engine gives a growling sound. ...
2
votes
0answers
20 views

Integrating Fast OBD Readings and GPS

I'm working on a project to look at fuel consumption on different roads and I need the OBD reader to log the GPS coordinates every time it takes a reading. I'm looking at instantaneous fuel ...
2
votes
0answers
31 views

Unable to connect OBD2 scan tool

Cheerz, I have purchased recently OBD2 scan tool(Autel MaxiScan MS300) which supports ISO9141. My car (Mitsubishi Lancer GLX 1.3 1999) seems like ODB2 compatible using ISO9141-2 protocol for ...
2
votes
0answers
324 views

OBD 2 Fuel reading says No Data

I wanted to read fuel level from the car and display it on my app. I'm using ELM327 bluetooth adapter to communicate with my car. When I'm sending the code "012F\r" to my OBD 2 it says "NO DATA". ...
2
votes
0answers
865 views

Mercedes Atego OBD2 live data codes

I have tried to connect an OBD2 ELM327 adapter in Mercedes Atego. Somehow I managed to get it in that OBD2 connector. I can see that my adapter is receiving electricity. These are the PID's that I ...
1
vote
0answers
25 views

Error MIL: off Spark ignition

I checked my OBD2 sensor and it shows on DTC that message. Along with P0171 system too lean on my Mazda 3. I put in an injen intake and that was 3 years ago. The check engine light came on 3 months ...
1
vote
0answers
1k views

Fuel Consumption and other Fuel related data from basic OBD-II parameters

I want to know how can i obtain the values of Fuel Consumption, Fuel Economy and other fuel related information from basic OBD-II parameters like Vehicle Speed, RPM, TPS etc. I have noticed that not ...
0
votes
0answers
21 views

linking a phone to a car via OBD-II and Bluetooth: Automatic (1st gen) in Europe

I am relocating to Europe soon, and I'm pretty sure my new car would have OBD-II. Why is Automatic adamant their current product is for the US only? Is it a regulatory issue, or something technical ...
0
votes
0answers
173 views

Remote Car Climate Controller

I am investigating the possibility of monitoring and controlling the car cabin temperature using GPRS. I will be using Arduino Uno and GSM shield to communicate with an Android App. The arduino works ...
0
votes
0answers
182 views

Error Message from OBD-II (7F 01 11)

I have been extracting OBD-II DATA from UART board (ELM327) on my TOYOTA INNOVA. It responded correctly few weeks before and gave all supported sensor values. But now, for every response, ECU responds ...