A two wheeled motor vehicle.

learn more… | top users | synonyms

-1
votes
1answer
96 views

Suggestions for replacing/upgrading exhaust/silencer for a 125cc Motorbike [closed]

I have a 125cc Yamaha Gladiator SS125, which is about 3 years old. I had my stock air filter (paper-based) removed and installed a K&N conical filter about a year ago. I wanted to know if anyone ...
1
vote
1answer
192 views

Why my bike shows petrol missing before 2000 RPM in all gears?

I am using Hero Karizma R (225cc, 5 gears). Recently I feel a missing in all gear befor 2000 RPM. Sometimes my bike turn off due to this missing. Usually it happens at 1st/2nd gears. After 2000 RPM ...
-1
votes
2answers
140 views

AJS Regal Raptor cranks but won't run

I have a AJS Regal Raptor DD125E. When I push the starter switch the engine spins but no spark at the plugs. However as I release the starter switch I get a spark from the plugs on the engine overrun. ...
2
votes
2answers
84 views

Find the version of a motorcycle

I need to know the exact version of my motorcycle, I can't find this information on the frame nor the user manual. It's a Kawasaki ER-5 sold in October 2005 in France. I want to replace the fork oil ...
-1
votes
2answers
24 views

Bikes power is iffy [closed]

Hi I have a 03 katana and for some reason the bike won't power on anymore...I turn the key and nothing no lights nothing. I'm not sure if it's the battery or what. What should I do to trouble shoot ...
3
votes
1answer
184 views

Rear wheel wobble

I recently took my '12 Yamaha R6 completely apart when I repainted it. When I put it back together I didn't realize but I'd forgotten a washer on the swingarm axle which was causing some movement of ...
2
votes
1answer
63 views

Mounting bar end mirrors on non-hollow bars?

I bought a CRG hindsight bar end mirror but the CRG adapters and all the adapters I find online seem to be for hollow bars. But the bars on my 12 Yamaha R6 just have a threaded hole for a bolt.
1
vote
0answers
29 views

BDL primary driver inner plate install [closed]

I am for the first time ever, in the process of installing a replacement Ultima 6 speed transmission with the same make and model on my 1994 Harley Davidson softail custom trike conversion. It has a ...
2
votes
1answer
161 views

Car and bike. How to keep it in good condition when unused for two months?

I've seen this post, this one and this one. But what about a bike like a Hero Honda Splendor+? Apart from keeping the fuel petcock off, what else should be done to ensure that the bike runs fine after ...
3
votes
2answers
251 views

Why is martensitic steel used instead of grey cast iron for ATV disc brakes?

Grey cast iron has better thermal properties -- conductivity and specific heat -- lower density, better castability, and better friction than martensitic stainless steel. Why are OEM parts made of ...
2
votes
2answers
213 views

Do I need to reprogram ECU when adding custom Air filter

I was thinking of replacing the air filter of a bike into a custom free flow filter. I understand that I have to mod the exhaust to free flow as well to accompany the increase in exhaust due to the ...
5
votes
3answers
429 views

Engine on BMW G650GS 2011 does not start when it's hot

I have a rather strange problem with my BMW G650GS. In the morning, when the engine is cold, it starts fine with a single crank. There is no problem with riding, the engine works fine and never ...
1
vote
2answers
164 views

Can someone identify this part of the engine on a TVS Apache

I tried looking up everywhere, and this is unique to this bike. Can someone identify the below component. Looks like a pipe connecting the engine with starter motor. Close up of the engine , both ...
11
votes
3answers
1k views

What are the Advantages of a Single Side SwingArm on Motorcycles?

I have noticed that Ducatis , Honda and Triumph have bikes with a Single Sided SwingArm Much like most of the scooters. Are there any advantages of following this design , if so why are not all ...
4
votes
1answer
629 views

Scooter break-in period - Actual scientific backing or urban legend?

I don't understand the break-in periods needed for scooters/motorcycles. I know everyone says it, but I haven't found any explanation with some scientific backing to not making it an urban legend. ...
4
votes
1answer
78 views

Fork tube seals Suzuki sv650

So I recently inherited a 2002 Suzuki sv650... It was garage kept for about 6 years and needs some love. I noticed that the rubber seals on top of the fork shock tubes won't stay with the tubes... ...
2
votes
1answer
158 views

A Suzuki GZ125 marauder that won't power on at all

I've been having a problem with my bike. I went to go to work in the morning and it turned on ok. Left to run for a few minutes then cut out. It turned over again and same thing ... I tried a third ...
5
votes
1answer
305 views

Honda CBR 250 won't start after heavy rains, puttering noise

There has been heavy rain and yesterday I couldn't start my bike. The main and other fuses are not blown. I ride it regularly. Turning the bike on: https://vid.me/pYNw. The high-pitch noise is not ...
4
votes
2answers
2k views

Bent front fork on a bike

There's a previously owned 2009 YAMAHA FZ16-S that I'm thinking of picking up. It has a slightly twisted and bent fork (plausibly caused by an accident). It's only apparent when you ride it for a bit. ...
0
votes
0answers
16 views

Yamaha fz700 brake and headlights problem [duplicate]

Recently bought a Yamaha fz700 bike. Headlights don't work whatsoever, checked fuses, bulbs, and I found that wires aren't getting any power. Flipping the Hi/Lo beam switch doesn't change anything ...
2
votes
2answers
274 views

My motorbike handle gets a hit when I hit a bump or pothole

My 2 month old bike is a 200CC Bajaj Pulsar (made in india) with only 2000kms on the odometer. I have ridden it carefully. I touched 100km/h accidentally on a drag race with my friend, just one time, ...
1
vote
1answer
75 views

Duke 390 Tyre rotation problem

I have observed that my ktm duke 390's back wheel is difficult to rotate even while its in neutral. If i'm riding the bike, if i put it in neutral, the bike slows down pretty quick than it used to be. ...
1
vote
1answer
144 views

Is Honda Shine Rear-Suspension claimable on Warranty\Extended Warranty [closed]

I own a Honda Shine (125cc) bike which started giving a less cushioning problem on its rear suspension since it was near to its second service (1200 km, 5 months from purchase). Though I told the same ...
2
votes
3answers
395 views

How do I reduce engine idling rpm without stalling it?

Considering idling losses are present in every engine, reducing the idling rpm might be providing significant savings. But, as I noticed on my bike, the chances of engine stalling increases with ...
5
votes
1answer
230 views

Carburettor jetting on installation of aftermarket air filter

I have a 150cc motorcycle and am planning to install an after market air filter(K&N) since the stock one was favoring fuel efficiency and not performance. The bike has a carburetor (Mikuni) not ...
3
votes
2answers
1k views

“tick-tick” sound in Enfield Clasic Motorcycle

BIKE ENFIELD CLASSIC 350 2013 Model ODOMETER: 14000 One and half year old Oil changed one and half month before general servicing. There is a particular sound from the engine while riding ...
2
votes
2answers
112 views

1987 Yamaha FZ700 headlights not working

I recently bought a 1987 Yamaha fz700, and the owner said the headlights didn't work, and I can't figure out what's wrong. We checked some of the wiring out, and the bulb connectors have no power ...
1
vote
1answer
617 views

Risks of “excess and lack” of Engine oil

I ride a Honda Stunner CBF 125 CC daily for approx 30 kms, with an average speed of 45 km/hr. I noticed that my motorcycle has been consuming too much engine oil like it not used to few years ago. ...
2
votes
1answer
325 views

Is it possible to check if the fuel filter on a Yamaha XJ600 is getting clogged?

Right after buying an used Yamaha XJ600N, I found that the rust in its fuel tank had clogged the fuel filter causing the motorcycle to lose power and until the engine died. The service station cleaned ...
5
votes
1answer
188 views

Yamaha FZS Ver- 2.0 Engine Seizure

I gave my bike (Yamaha FZS ver 2.0) to an authorized service center for it's first-time service. The mechanic didn't fit the drainbolt (which is under the engine) properly causing the engine oil to ...
4
votes
1answer
145 views

How to improve suspension on my bike TVS Star City 110 CC 2012 Model

I ride a TVS Star City 110 CC 2012 Model bike weighing 109 Kgs. I am feeling uncomfortable with the bike suspension. When I checked with my mechanic, he said it is fine. I can feel it is jumping even ...
2
votes
1answer
39 views

Derbi Cafe 125 stalling when changing to 1st

I have a Derbi Cafe 125. This morning I started the bike up, let it run for a few minutes, changed from N to 1st, and the bike cut out. This happens repeatedly until I walked to work. I then realized ...
4
votes
2answers
114 views

Lost torque on my Yamaha XVS650

I have a Yamaha DragStar 650 1999. I have a Highway Hawk exhaust and I removed the baffles. Now the exhaust is completely open. When the engine is cold I can start it only if I pull the acceleration ...
4
votes
1answer
88 views

Honda XR650l first ride after winterization

Before winter I had the oil changed, filled the gas tank and added the recommended amount of Sta-bil fuel stabilizer. Then rode around for about ten minutes then switched the petcock to off and ran ...
4
votes
2answers
314 views

Semi synthetic oil engine break-in

I've finished rebuilding the engine of my motorcycle (4 stroke 650cc single-cylinder). For now it runned only once varying between 1000 and 2000 RPM for 5 minutes with a couple of short bursts after ...
2
votes
1answer
170 views

What kind of technology is used to create this “The Self Balancing Electric Motorcycle”?

In this video , the commentator said that the vehicle uses some kind of technology to keep the Motorcycle self-balanced. That means it won't fall over even with an outside impact force. Since my ...
6
votes
1answer
611 views

Clutchless Downshifts Using Throttle Blip on a Motorbike/Sequential Gearbox

This is with respect to non synchromesh, sequential transmission. Ducati along with several after market systems, implement clutchless downshifts by automatically applying a slight throttle to unload ...
0
votes
2answers
70 views

Can a 41mm shock be replaced in Bajaj Pulsar 150 by removing the company fitted one?

Can the OEM shock be replaced on a 2008 Pulsar 150? I would like to remove the OEM shock and replace it with a 41mm aftermarket model.
3
votes
1answer
57 views

Partially blowing a motorcycle main fuse?

So in the continuing saga of my 81 Suzuki GL450L I have been making continuing improvements to the electrical. The coils as previously found were definitely an issue, but possibly not 'the' issue. ...
5
votes
1answer
49 views

Alternative location for motorcycle ignition coils?

I recently replaced the ignition coils on my 81 Suzuki 450. The aftermarket coils are just large enough that the tank won't seat right, even after adjusting the bracket. Would there be any issue in ...
5
votes
2answers
685 views

Why are gears designed in this pattern in motorcycles? [duplicate]

On motorcycles with manual transmissions, the shifting gears goes (down to up) like this: 1st Gear (all down) Neutral (half up) 2nd (full up) 3rd (so on) What is the logic behind this? Wouldn't ...
2
votes
1answer
467 views

What is Total litres (reserve, usable)15 litres (3.2 litres reserve, 2 litres usable)?

I bought a new bike(Pulsar 150), and while reading its specs in the user manual i found Total litres (reserve, usable) = 15 litres (3.2 litres reserve, 2 litres usable). what does this mean, I assume ...
3
votes
4answers
700 views

How often can I reinflate my tire

How often should I reinflate my tire. My bike has tubeless back tire and tubed front tire. Currently I am reinflating once in a week with 35psi(back) and 25 psi(front). Should I need to reinflate my ...
1
vote
0answers
152 views

Yamaha FZ 16 loses smoothness too soon [closed]

I have a 2008 model Yamaha FZ. Lately, I have observed that the first week after a service, the motorbike is super smooth with good pickup. But after that it loses its smoothness and becomes dull.... ...
7
votes
1answer
512 views

Idling issues on 1995 Kawasaki ZZR600

The bike was running rough and could not get a constant idle speed. I checked the air filter and it was pretty well shot (contamination, etc.). As I awaited delivery of the new air filter, as a test I ...
5
votes
1answer
583 views

No spark on my new motorcycle

I recently purchased an 81 Suzuki GS450L, my very first bike. I'm not getting a spark. When it dies, it does so silently. No backfire, sputtering, etc. My first thought was that it had aftermarket ...
5
votes
1answer
547 views

I dropped my bike and now it won't start

I have a Suzuki GSX 600F Katana. Yesterday, I changed the clutch lever on the handlebar and left the key on. I had to push start my bike. After getting it started, I left it in first gear, and let go ...
5
votes
2answers
901 views

Royal Enfield Classic 350 - Motor Break-in Best Practice

How many km's should be driven with a lower speed to setup the bore for a Royal Enfield Classic 350, what is the minimum speed for that duration and how many km's should we maintain that lower speed?
5
votes
2answers
281 views

How easy (is it possible) for an amateur to change the drain tube of a motorbike fuel tank?

The bike is a 1998/99 Honda CBR 600F. The drain tube seems to be corroded inside the fuel tank, based upon 2 symptoms: Filling the tank more than 3/4 full causes petrol to drain from the drain tube ...
4
votes
1answer
315 views

Old gas in 2 cycle engine

I have a 2 stroked engine that sat for over 2 years. I drained the gas and can get it to turn over when I put starter fluid in the carb. it is blowing out a water substance from the muffler and cuts ...