questions regarding manual transmissions and gearboxes

learn more… | top users | synonyms

5
votes
2answers
47 views

What does “clutch grabs hard” mean?

I recently had an engine swap done and will pick it up soon. Mechanic swapped in a 6 puck competition clutch as well. Combined with a very light flywheel(same weight as I'm used to driving, 8 lb), ...
6
votes
2answers
130 views

Engine continues to spin after putting in neutral

I have a 2001 Plymouth Neon, it has a manual transmission. Recently the car has started to not stop the engine when I shift into neutral. If I shift into neutral while moving, the engine will rev like ...
2
votes
1answer
24 views

Engine surges when depress accelerator past a certain point

I have a 2003 manual Nissan Almera S petrol 1.5L with only 75,000 miles on the clock. Today the engine has started to surge. If I depress the accelerator pedal more than approx. ½ inch - 1 inch, the ...
1
vote
1answer
49 views

What is happens to the brakes when an automatic drives below the speed for 1st gear with no added gas?

In a manual transmission car, when a driver wants to go below the speed the car travels at in first gear with no added gas using the gas pedal, you ease off the clutch, reducing the amount of power ...
1
vote
1answer
55 views

Is it normal for the car to vibrate on the BITE when no gas is given in a manual transmission?

Is it normal for the car to vibrate on the biting point when no gas is given? When I give enough gas it seems fine but not when I very slowly release the clutch and hold at the biting point. Is this ...
2
votes
1answer
45 views

What is rev matching, and how do you do it correctly? [closed]

I understand that not doing this properly will destroy your transmission/synchros. What's the proper way to do it? I think I'm doing it right, but I've found most people's descriptions to be vague and ...
2
votes
1answer
58 views

what damage or extra wear (if any) is caused by turning over the engine while in gear (manual transmission)?

While newer cars never allow you to turn over the engine without the clutch depressed, in some older cars, if you do leave the transmission in gear, do not depress the clutch and turn the key, the car ...
5
votes
2answers
250 views

Why does my 2016 Mustang GT Manual jolt/thud when I shift?

I just learned how to drive manual in my 2016 Mustang GT. It has 3300 miles on it. It makes a "thud" noise when I put the stick into low gears (1,2,3) sometimes. This noise makes the car jolt, such ...
2
votes
1answer
33 views

Honda City vTec Slow Start

I have a Honda City 2005 vTec Manual Transmission Car, which will be due for servicing in another 1000KM. I am not well used to driving manual car and I face a lot of traffic everyday going and ...
2
votes
1answer
120 views

Why does my clutch “bounce”?

'97 Jeep Wrangler 4.0L, though I doubt the phenomenon is that specific. Sometimes, when I accelerate normally from a light or a stop sign (at the same rate as everyone around me) while keeping the ...
4
votes
1answer
89 views

95 Honda Del Sol Si manual won't go into gear when idle > 1000 rpm

I have been racking my brains over this very odd issue. Here is the problem. I recently got this car (95 Honda Del Sol Si 5 spd 160k miles) as a second car. The previous owner claimed that the clutch ...
2
votes
1answer
65 views

Hesitation in RPM drop when shifting manual transmission, 2007 Mazda6

I recently said goodbye to a 2002 Mazda Protege that made it to just over 300,000 miles. So naturally I purchased another Mazda - 2007 Mazda6, 5-speed manual, 91k miles. Besides the difference in ...
3
votes
1answer
163 views

Manual Transmission- Can bad shifting destroy transmission

Been driving a car with a manual transmission for 6 years. I never had to replace the clutch but the transmission recently blew up on me. I was aware that my car was leaking transmission fluid for ...
6
votes
3answers
3k views

Is it bad to drive slow at low rpms in 4th or 5th gear? Do you get better gas mileage?

Obviously running your engine at too high an RPM for too long isn't good. But what about running it too low? not so low that it stalls or lugs, but within around 1,000 RPM? Would you get better ...
1
vote
1answer
84 views

2005 Mini Cooper manual transmission stuck in between gears

Trouble started popping out of 5th gear, then also 2nd gear, then all the gears. Then it wouldn't go into gear, it would go in if I gave it gas, enough to get it home. I was able to drive it to a ...
1
vote
1answer
75 views

My clutch cable has been stretched and since tightened to fix it. Should I replace it?

I have a VW Polo 2001, 37000 miles, manual transmission, 1.4 engine, with a replaced clutch and timing belt, and a reconditioned gearbox. I didn't face any resistance in my pedal last night. The ...
3
votes
1answer
798 views

Is vibration for a new clutch job normal?

I have a 2005 Toyota Camry (Manual Transmission). My clutch died on me last week - couldn't accelerate. I had the clutch replaced at a local mechanic. Now when I start the car off in first gear the ...
3
votes
1answer
50 views

After long journeys, gear slips in 5th, but not into neutral

This is a follow up to another question I asked. I've managed to get some video of it happening this time. It started happening after travelling for about 2 hours. I was experiencing heavy traffic. ...
5
votes
1answer
265 views

Minor grinding noise and vibration when car is idle

I have a 2005 stick shift Toyota Camry. Sometimes when I am at a red light or stop sign and the car is in neutral I feel a slight vibration from the pedals and a slight grinding noise coming from the ...
2
votes
1answer
320 views

5th gear slipping of 5th gear at 3000 revs, but not into neutral

I'm planning to take my car to Mr Clutch on soon, but I wanted to see what every else's impression is of my car's problems. Last night I was driving along the motorway, accelerating to 70mph, when ...
1
vote
2answers
61 views

Where can I find a reference for Honda part numbers?

Where can I find a manual or detailed catalog or service manual of a specific car in order to know for example all its part codes to buy original replacement parts, from pieces and paint (Not owner's ...
4
votes
1answer
38 views

ok still not working right 95 Geo Tracker clutch

IRT this question ... At first I thought I had it good (the clutch) now it idles too high and the peddle won't come all the way back up. I can't put into first or second and I'm at a loss not sure how ...
3
votes
3answers
96 views

1995 Geo Tracker - Shifting Issues

I just put in transmission fluid and replaced the clutch cable. I've re-adjusted it (not that I have much if a clue on what I'm doing). It did good for a few days then I had a problem with 2nd gear ...
3
votes
1answer
158 views

What causes my Mustang to buck when I let off the gas at a high RPM?

I have a 2007 Mustang GT, 4.6L V8 with a 5-speed manual transmission. This is the car I learned how to drive stick on, and the only other car I've ever driven with a manual is a 1963 pick-up truck... ...
2
votes
2answers
243 views

Manual Transmission Grinding Occasionally Shifting Into Fifth

I have a 99 Nissan Almera which occasionally grinds / doesn't engage when I try and put it into fifth gear. Not often, but maybe once or twice a day. I'm not sure if the problem is operator related, ...
1
vote
1answer
127 views

Reverse grinds and transmission won't lock into 1st gear [closed]

I have a 2001 Ford Escort ZX2 with manual transmission. It has had noticeable play in the shifter but had no problems until suddenly the clutch just would not engage after being pushed down ...
3
votes
3answers
2k views

What will happen in result of the failure of a clutch release bearing?

I drive a 88 Mazda RX-7 non-turbo 5spd. The previous owner claims the clutch was done last July(little under a year ago) and I have no reason to doubt such claims. I do believe the clutch release ...
1
vote
1answer
241 views

Achieving least wear on clutch when changing gears? [closed]

I want to do the least wear on my clutch on a manual car. I only recently passed the test and I wonder if I ever learnt to use the clutch efficiently. Here's how I change gears: foot of gas press ...
3
votes
1answer
76 views

Grinding when shifting into 1st from a stop

My car (2013 Ford Focus, 12k miles, 5 speed manual) suddenly started to grind when shifting into 1st from a stop about halfway through my commute home. I realized that if I depress the clutch for long ...
4
votes
2answers
4k views

Manual transmission difficult to put into gear. Do I need a new clutch?

I have a 1998 Jeep Cherokee Sport, manual transmission (the 6 cylinder model, I believe 4.0L). It has 4 wheel drive. I've lent the car to some friends recently who were 'rusty' with their manual ...
1
vote
1answer
208 views

Are you supposed to give the engine gas when shifting gears? [duplicate]

I'm learning how to drive manual. When I switch gears, I just stop giving it gas, push in the clutch, select the gear, and let out the clutch. After the clutch is out, I give it gas. This works ...
1
vote
1answer
622 views

95 honda civic ex, smoking heavily from exhaust

I have a 95 honda civic ex (manual), and it smokes really bad from the exhaust. It's thick white smoke that lingers, and it also burns oil, but when checking the oil, it is not clouded up or milky or ...
3
votes
0answers
28 views

Clutch/transmission noise [duplicate]

I have a manual transmission in a Ford Ranger with 240,000 miles and it has recently started making an intermittent grinding/grating noise. The conditions under which I have heard it are: Clutch is ...
3
votes
1answer
196 views

Foot slipped off clutch while downshifting. Damage?

I have an '08 Honda Fit with a 5-speed manual transmission. I hit a steep hill earlier today and decided to downshift from 3rd to 2nd, so I didn't ride the brake for several miles. Before my RPMs ...
3
votes
1answer
502 views

Will a worn clutch ever completely fail to engage? If not, what will cause this?

I've noticed my clutch beginning to slip for maybe a month or two; it was slower to engage, but not badly enough to affect driving. Over the last week or so, it was getting significantly worse every ...
2
votes
1answer
92 views

2006 manual transmission. Diesel Jetta.

My Jettas gear shift is not working properly. It's hard to pull out of reverse and it sticks getting into first and second. After first and second shifting is simple. I'm sure it's not the cluTch. My ...
9
votes
2answers
15k views

Clutch less shifting - why does it work? Is it bad?

I have been driving stick for 15 years and within the last year I learned I can shift gear without the clutch. Normally the transmission will not let me shift gears without using the clutch. ...
4
votes
2answers
1k views

1st gear hard to engage unless stopped, Subaru 2004 Impreza Outback Sport

Since I've bought my 2004 Impreza Outback Sport, I've had a problem with shifting into 1st gear. First gear is generally difficult to engage while moving. You can just force it, but it's really ...
5
votes
3answers
976 views

Did I damage my car by trying to move in reverse with the handbrake on?

I was in a hurry to leave for the office yesterday and forgot that my handbrake was engaged while starting. I started the engine, clutched, and reverse geared, and found the vehicle not moving ...
2
votes
1answer
148 views

Clutch or damaged 5th gear?

Just trying to figure out whether my car's issue is a worn out clutch or a damaged 5th gear. Going up through all the gears, there's no resistance, slipping, grinding or any other suspicious noise. ...
3
votes
0answers
137 views

95 manual civic… loud knocking sound when decelerating [closed]

I have a 95 civic lx standard ... Recently on way home from work it started making a knocking sound after I let go of the gas . I pulled off fwy put it up on two jacks engaged gears accelerated then ...
2
votes
2answers
803 views

Engine braking vs. braking in neutral on slippery & normal conditions [closed]

I've driven manual transmission for over 2 decades, and I've been braking by downshifting with rev matching for about one decade. I recently heard a radio show host advise people to drive carefully ...
6
votes
1answer
777 views

Sometimes my second gear is rough to engage. What could be wrong?

So I've got an odd problem for a 2004 Toyota Echo. The second gear, sometimes not always, is hard to engage. If I be real gentle, and just put a bit of pressure, it would slip in. I could also be a ...
3
votes
2answers
902 views

Difference between “dumping the clutch” and N->D in an auto?

What's the difference between dumping the clutch, and going from N->D at high RPMs with an automatic transmission? Will this cause any damage to the vehicle?
10
votes
2answers
13k views

WHY does an engine stall? (manual transmission)

Before you write off my question as one that's been answered a million times already, I want to clarify. I understand that the engine needs to go a certain rpm and when you try to engage the clutch ...
2
votes
1answer
8k views

Honda Civic Clicks but won't Crank

I have a 2005 Honda Civic and today out of the blue it wouldn't start. I hear a click sound when I turn the key to start, but nothing else. The car lights still work, and they dim slightly when ...
0
votes
2answers
136 views

Impact/Effect on handbrake when parked on incline?

If a 2-2.5 (between two and two-and-a-half) ton saloon car: is manual between 7-15 years old parked on an incline of around 20-30 degrees for roughly 8 hours a day 5 days a week What can the ...
0
votes
1answer
602 views

manual transmission issue when changing 3rd gear with polo 3 1998

I'm currently driving a 1998 Polo 3 known 6n (1.0 petrol) and i have issue when changing my 3rd gear, especially when the car is cold. It pop out while i'm changing 3rd gear and other times it will be ...
2
votes
1answer
359 views

Why are gears still grinding after replacing transmission, clutch, and hydraulic cylinders?

Cavaliers are known for transmissions going bad, and my Cavalier's transmission was making a horrible grinding noise going into fifth. Double clutching seemed to be working until it started grinding ...
1
vote
1answer
79 views

My 1991 Honda Accord grinds on third gear!

My 1991 Honda Accord grinds on third gear what could this mean and how can I fix it?