Internal Combustion Engine. Most engines in road going vehicles are 4-cycle internal combustion gasoline engines.

learn more… | top users | synonyms

8
votes
1answer
116 views

How often do you need to run a car?

I have a car that is garaged and not used much. How often should I take it out for a drive and for how long each time? I currently get it serviced every 10,000 KM.
8
votes
1answer
409 views

Carburettor jetting on installation of aftermarket air filter

I have a 150cc motorcycle and am planning to install an after market air filter(K&N) since the stock one was favoring fuel efficiency and not performance. The bike has a carburetor (Mikuni) not ...
8
votes
1answer
614 views

Two-stroke dirt bike piston running into spark plug

Recently, I submitted a post on here regarding a broken ground electrode on the spark plug of my 2005 Suzuki RM125: Bottom piece of spark plug broke off in motorcycle engine Well, I found out what ...
8
votes
2answers
805 views

Can you stop fuel delivery to one cylinder of a 2003 Ford F150 with 5.4L Triton Engine?

Can you disconnect a wire so gas will not pump into the cylinder? I have a spark plug blown out and need to get my 2003 F150 5.4 Trition engine home without paying another tow charge.
8
votes
3answers
192 views

How to work on engine out of car?

I'm currently doing an engine swap on on 97 Corolla Levin, need to swap over the exhaust manifold, water pump etc from one engine to the other, but not sure what the best way to handle the engine ...
8
votes
5answers
14k views

Doing my own fuel induction service - how to, and how difficult?

I was recommended to get a fuel induction service for a 2002 V4 Camry, and am considering doing it MYSELF. The reasons for considering this are: My car idles a bit rough, especially when the AC is ...
8
votes
1answer
88 views

Can't find schrader valve

I have a 89 camaro with a 350 engine, where can I find the fuel valve where I connect the fuel pressure tester? I looked up videos on where it's located but mine doesn't seem to have it, is there ...
8
votes
1answer
64 views

Would bored out 307 need new heads

I have a Chevy 307 with casting number 3970020 and everything I've read says this particular block can be bored out to 4" effectively making it a 327. I plan to have my machine shop test it and make ...
8
votes
1answer
10k views

OHV vs. OHC: which is faster in speed, horse power?

What are the main differences in OHC and OHV engine designs, and which is faster or more powerful? Also, which is more reliable?
8
votes
1answer
92 views

Pneumatic Valve Spring Operation in Formula 1

In the 2006 Formula 1 World Championship the rules allowed for pneumatic valvesprings. These engines were required to have a 90° V8 engine with 2.4 liters of displacement, 4-valve-per cylinder layout ...
8
votes
2answers
3k views

Low power, bad gas mileage, smelly exhaust after engine work

My 92 Civic has had low power (need to use at least one gear lower than usual to get the same power) and has been getting bad gas mileage (15-25mpg vs 32-42 mpg usual) since I replaced the head gasket....
8
votes
1answer
1k views

What do i need to know when replacing a valve cover gasket

I have an oil leak from a cracked valve cover gasket that i want to replace myself. I bought the gasket nearly 6 months ago and i am apprehensive at doing it myself without sort of feed back as to ...
8
votes
1answer
49 views

2006 VW Jetta TDI EGR cleanup

I am going to cleanup the EGR pipe in my VW Jetta TDI. Are there any special considerations on how to remove the carbon which might be blocking the flow?
8
votes
1answer
55 views

Roller rockers to a stock valve train

78 Nova but the engine is from a different car; casting # V0707CMH. I have a 350 with 305 heads. Stock valves, pushrods, cam, and lifters. The nuts on my stock rocker arms are in need of replacement; ...
8
votes
1answer
163 views

newly rebuilt engine, long warm-up & severe shaking

I have a 2002 Toyota Celica GT with a newly rebuilt engine (ran out of oil and threw rods) but problems still persist. I was told by the mechanic to allow myself a 500 mile break in time of not ...
8
votes
2answers
62 views

Proper glow plug operation

Are glow plugs supposed to stay on after the engine has started to help with the firing of the first few revolutions?
8
votes
0answers
199 views

Clunking sounds when decelerating or idle with clutch engaged

I have an issue with a 2010 Opel / Vauxhall Insignia 2.0 CDTI Sports Tourer (aka Buick Regal in the States if I'm not mistaken) and I'm having difficulties pinning it down. It's going to be a lengthy ...
8
votes
0answers
635 views

Strange surging and like it's going to stall, hesitant whilst idling

I have been having an issue with my Peugeot 207 (2008 model) 1.6L VTI petrol engine. The cam cover was replaced by the garage but hasn't fixed the problem. I have lost faith in them. I managed to ...
8
votes
2answers
531 views

Fiat Punto Wont Start. Fuel Light & Three warning lights flashing

My Fiat Punto 1.2 Year 2000 MK2 (I believe) will not start. The engine turns over but the car won't start. The fuel light is flashing and petrol gauge says empty which isn't the case. There are three ...
7
votes
4answers
2k views

why do engines have so much unused horsepower?

I've looked at the power rating of an engine used in a Humvee (5500 lbs) and was surprised it's only ~190 horsepower, which is exceeded by many 4 door sedans. So an obvious question is why doesn't my ...
7
votes
3answers
1k views

Do valves rotate over time?

As I was doing my valve servicing, one question came to mind: As valves undergo millions of cycles of reciprocating motion, do they actually rotate or is their position relative to the seal fixed? Or ...
7
votes
4answers
36k views

Is engine braking harmful? [duplicate]

Possible Duplicate: Does Downshifting (Engine Braking) Cause Extra Wear and Tear? My wife and I have a disagreement about a practice of mine--engine braking. When I'm driving her manual ...
7
votes
2answers
565 views

Two-Stroke Diesel Engine - Do they use forced induction on them?

As I have indicated before, I'm very diesel ignorant. I just know the basics, very basics. In a two-stroke diesel engine using forced induction seems necessary but at the same time I see challenges. ...
7
votes
6answers
44k views

How to get a motor to Top Dead Center

I'm not sure how specific to my car this is or not, so I will include my car information just in case: It's a 1991 Honda CRX, base trim(the motor is the d15b2). On to the question: How do I go about ...
7
votes
4answers
3k views

Why does my car scream on cold start?

My 1988 Subaru XT6 2.7L engine screams at me on a cold start then it will stop and then do it again when I take it out of park, but then it stops. Also, my car is losing antifreeze. Any ideas why?
7
votes
3answers
2k views

What kind of engine oil should one use in a diesel?

I got an 1987 Toyota Land Cruiser with a 2H diesel engine. I never changed oil on a diesel engine prior to this truck, so I'm a little confused. Toyota Factory Shop Manual recommend API CC oil type, ...
7
votes
2answers
679 views

What are all the different types of fluid in a car and a short summary of their use?

A fluid is defined as anything that flows, hence for our purposes a gas or a liquid. I know that there is fuel, engine oil, engine coolant and brake fluid. Also air is normally taken in through a ...
7
votes
3answers
20k views

What is a rod knock?

What is a rod knock? What causes a rod knock, how bad is a knocking rod, and how can I tell if a rod is knocking?
7
votes
2answers
344 views

How do modern engines differ than older ones

Modern engines produce more horsepower with more fuel economy but with the same procedure of burning the fuel air mixture and moving the piston, but the old ones and new ones are both four cylinders ...
7
votes
3answers
167 views

What are some typical maintenance things that every owner should do regularily?

Right now I just get a car wash every month, and my oil changed and whatever is included in that. Usually just a quick "inspection". Is there anything else I should be doing for my car? Or also, is ...
7
votes
1answer
641 views

What is a head?

Due to this question I now have a fairly well-rounded understanding of what a head gasket is. I assumed that sometimes, when people would talk about "heads" that this was just an abbreviation of ...
7
votes
5answers
76k views

Cold start squeaking noise in engine

I just purchased a used 2010 Corolla 3 days ago. I've only now noticed that when I start the car, there is a squeaking sound coming from the engine. It lasts no more than a second. Sounds like it ...
7
votes
3answers
8k views

Is it bad to drive slow at low rpms in 4th or 5th gear? Do you get better gas mileage?

Obviously running your engine at too high an RPM for too long isn't good. But what about running it too low? not so low that it stalls or lugs, but within around 1,000 RPM? Would you get better ...
7
votes
3answers
101k views

Car temperature displaying below Cold or just above Cold always?

I've noticed on my 94 Integra (bought used about 2 weeks ago) that the thermostat is often below cold, sometimes above cold but never up to the center mark. Today I was boiling inside my car as it ...
7
votes
1answer
222 views

Scatter Camshafts - What are they and why do I want one?

It seems in the world on mini's as in Mini Cooper, there is a camshaft called a scatter cam. It changes the timing for cylinders 2 and 3. I've heard of changing the timing to have 1 and 4 firing at ...
7
votes
2answers
109 views

Shouldn't a loss of compression equal a loss of power?

I recently did a compression test on a Nissan B13 GA16DE and got 125, 127, 122 and 140 psi (cold). A few years ago, all 4 cylinders got 135-140 psi, cold. Shouldn't this loss of compression have led ...
7
votes
2answers
720 views

How can I be sure that a rod knock is actually a rod knocking?

I have a 2005 Ford Escape 2.3 L engine, there is a knocking type sound as soon as the engine is started and the speed of the "knocking" follows the RPM. How can I be sure that it is in fact a rod ...
7
votes
1answer
217 views

What should one do to reduce the HP lost at the wheels on an automatic transmission?

I have a 1990 Toyota Supra Turbo 4 speed auto. I've done some research about automatic transmissions and manual transmissions and what are the positives and negatives of each. (For example, MT is said ...
7
votes
2answers
339 views

Why do engines run badly below the normal idle speed?

When the engine speed in my petrol car drops below about 650-700 RPM - the normal idle speed - it starts to shake and judder. This could be because say, I didn't give enough gas when pulling away. ...
7
votes
3answers
2k views

Infamous WRX/XT overheating problem

I need some help figuring out what's wrong with my 2007 Forester XT Manual. Background: The headgasket popped in November of last year. I had it fixed by an RMI certified workshop. They skimmed the ...
7
votes
1answer
471 views

Why are V engines less smooth?

I'm learning how to ride a motorcycle on a Suzuki Gladius SFV650, with a V-twin engine. But I also had the chance to ride a Kawasaki ER-5, which has a parallel twin engine (550cc). I've noticed that ...
7
votes
4answers
36k views

Diesel Engine difficult to start

I have a diesel powered Audi A4 B7 (2006) 2.0TDi (the 170BHP variety) with a manual gearbox, which I've owned for around 18 months. The car has just short of 100k miles and has a full dealer service ...
7
votes
5answers
367 views

What can cause a gasoline engine to suddenly & mysteriously stop (non-catastrophically)

I was thinking about this question and found myself wondering what could cause a gasoline engine to suddenly stop, and then be restartable? So not things like running out of fuel, or suffering a ...
7
votes
3answers
625 views

Okay to add new oil to old?

Title pretty much explains, I change my oil every 4-6k miles depending on how generous I’m feeling, however will the oil dirty oil that’s already in the sump mix with the clean oil when topping up? ...
7
votes
1answer
213 views

How do old cars actually lose horsepower?

I have heard that when a car gets old it slowly but surely loses its horsepower to some degree. For example, I used to drive a 1997 Ford Fiesta with a 1.25L 1242cc engine that supposedly produces a ...
7
votes
3answers
310 views

Can a valve suddenly break in half? Versys 650 destroyed engine

this week-end, I had to disassemble an engine from a kawasaki versys 650 (early). The bike lost power while making ugly metal sounds. It never started again. RIP. context: 108.000km, mostly higway ...
7
votes
2answers
2k views

2004 Ford Focus engine cover would not budge after all screws are removed

I have a 2004 Ford Focus SE 2.0L. There’s some oil leak on the engine. A mechanic told me it could be the engine valve gasket being cracked (the car is pretty old and never had a valve gasket change). ...
7
votes
3answers
7k views

Motorcycle popping on acceleration

I have a 1975 Honda XL250 that I bought earlier this summer. Up until recently its been running great. It was leaking a little gas, but nothing too serious. When it started to get worse, I opened up ...
7
votes
2answers
125 views

How can head port volume affect the power curve of an engine?

Recently I learned that even more things other than the ones already mentioned here can effect the power curve that is produced by the engine. Here is an example of one. I understand that there are ...
7
votes
3answers
2k views

What actually happens when there is not enough coolant in a car engine?

I know that a lack of engine oil can destroy an engine, so I was curious as to whether it is just as bad to drive a car with a very low engine coolant. What is engine coolant? What exactly are all ...