The clutch disengages the engine from the gearbox in a manual-transmission car, enabling the driver to change gear.

learn more… | top users | synonyms

2
votes
1answer
38 views

I get a blast of hot air during stop start driving. What could cause this?

I am a learner driver with a Hyundai i20. Every now and then when I stop and then go and switch to second gear I get a blast of heat at my legs and feet. The aircon is off and its a diesel. I am ...
2
votes
1answer
17 views

Do I have to change the chaincase lubricant when adjusting the clutch during routine maintenance? 2015 HD Road King

I am completely new to motorcycle maintenance, but need to adjust my clutch. I have watched a demonstration video for a similar model (I think) - but couldn't find an exact match. Since I will be ...
2
votes
1answer
32 views

5th gear slipping of 5th gear at 3000 revs, but not into neutral

I'm planning to take my car to Mr Clutch on soon, but I wanted to see what every else's impression is of my car's problems. Last night I was driving along the motorway, accelerating to 70mph, when ...
1
vote
0answers
10 views

ok still not working right 95 Geo Tracker clutch

IRT this question ... At first I thought I had it good (the clutch) now it idles too high and the peddle won't come all the way back up. I can't put into first or second and I'm at a loss not sure how ...
3
votes
3answers
22 views

1995 Geo Tracker - Shifting Issues

I just put in transmission fluid and replaced the clutch cable. I've re-adjusted it (not that I have much if a clue on what I'm doing). It did good for a few days then I had a problem with 2nd gear ...
2
votes
1answer
186 views

Clutch is stuck disengaged and pedal will not move

My clutch pedal on my 2005 Toyota Corolla will not move. I can start the car by pressing the clutch safety switch by hand. I can put my transmission into gear with the engine running, so the clutch ...
3
votes
2answers
156 views

Jeep JK Clutch vs Slave Cylinder

I have two different opinions on whether a clutch should be replaced when a slave cylinder fails: It WILL coat the clutch plate and will wear the clutch plate. The clutch plate MUST be replaced. ...
2
votes
2answers
38 views

Manual Transmission Grinding Occasionally Shifting Into Fifth

I have a 99 Nissan Almera which occasionally grinds / doesn't engage when I try and put it into fifth gear. Not often, but maybe once or twice a day. I'm not sure if the problem is operator related, ...
6
votes
2answers
52 views

how a clutch works

I understand how a clutch can separate the flywheel from the clutch disk so that power is disconnected from the engine but how when that happens, the input shaft (along with the countershaft) stops ...
6
votes
1answer
3k views

Clutch less shifting - why does it work? Is it bad?

I have been driving stick for 15 years and within the last year I learned I can shift gear without the clutch. Normally the transmission will not let me shift gears without using the clutch. ...
1
vote
1answer
91 views

Vauxhall Astra diesel replacement clutch

Could someone let me know if a clutch and flywheel is changed on a Vauxhall Astra diesel do they change the gearbox oil as part of the job. Many thank
2
votes
1answer
130 views

Ford Ranger manual transmission randomly squeals in 5th gear

My clutch started to slip and was squealing so I had a new clutch, flywheel, slave cylinder, pilot and throw out bearings all replaced. It drives fine, but it randomly makes a loud squeal in fifth ...
3
votes
3answers
91 views

What will happen in result of the failure of a clutch release bearing?

I drive a 88 Mazda RX-7 non-turbo 5spd. The previous owner claims the clutch was done last July(little under a year ago) and I have no reason to doubt such claims. I do believe the clutch release ...
1
vote
3answers
82 views

Safe engine braking in automatic cars

When I was learning to drive, I took my lessons in a manual car. On one of the lessons I was performing a reversing maneuver and I controlled the car on both the clutch and the brake pedal... which I ...
3
votes
1answer
25 views

Is the knock an early sign of Dual Mass Flywheel problem. Main dealer says acceptable noise?

Ford Mondeo 2012 1.6 TDCi DPF SS 115. At 15,500 mls I am experiencing a knocking sound when raising the clutch pedal but only when the engine is running. The sound outside the car is really loud. It ...
3
votes
1answer
95 views

Craftsman lawn mower won't move

My son was cutting the grass the other day and stopped. After he stopped the lawn mower wouldn't go into gear. 1-6 or reverse, nothing. The blade still engages and turns however it seems to have an ...
0
votes
1answer
129 views

Ford Fiesta and Focus Clutch Issues

I am in the UK and I am currently planning to get a Ford Focus/Fiesta depending on the budget and features. I have viewed 2 Fords so far - a Focus (100K miles, 2001 model) and a Fiesta (35k miles, ...
0
votes
2answers
319 views

Noise when pressing clutch pedal

I have a Saab 900 and when I press down on the clutch pedal to change gear it makes a rasping noise? Could someone tell me please is this serious?
3
votes
3answers
924 views

My mechanic asks me to press the clutch padal while starting engine during winter

Does he mean to say that my engine doesn't disengage completely when the clutch is released, if that's the case then my clutch would wear out. Am I correct in thinking so?
9
votes
4answers
7k views

Causes of early clutch failure EXCLUDING driver style

UK 61 plate, Ford Diesel Mondeo Estate, Econetic: clutch replaced at 31,800 miles; failure caused by 'driver style' I use my car daily for commuting and for business. It's supplied to me as a company ...
4
votes
0answers
217 views

What is this part and how do I remove it?

I am trying to replace my motorbike clutch friction plates, but cannot remove the basket around the plates ( I think that's what people mean when the say 'basket' - the cover over the plates that ...
1
vote
1answer
2k views

Broken Clutch Linkage Under Dash on 1987 Ford F150 4x4

On the way to work Thursday morning, the clutch pedal sanpped to the floor when I pressed it, and it stayed there. It was still in gear, and I was able to limp to a parking lot. I looked under the ...
1
vote
1answer
46 views

Reverse grinds and transmission won't lock into 1st gear

I have a 2001 Ford Escort ZX2 with manual transmission. It has had noticeable play in the shifter but had no problems until suddenly the clutch just would not engage after being pushed down ...
2
votes
1answer
50 views

Clutch issue in 1995 Mazda Miata

My clutch pedal had absolutely no pressure unless I would pump it, but that wouldn't do much. It finally gave out so I changed the master cylinder next to the break cylinder with one that I know works ...
5
votes
1answer
81 views

2002 Peugeot 206 Clutch won't disengage

When the car is running, I am no longer able to put it into any gear; like it would happen when you're not holding the clutch, so that is one of the reasons why I think there is something wrong with ...
4
votes
2answers
5k views

Clutch pedal suddenly doesn't go deep enough to engage gears

I was driving normally (no problems, everything going smoothly; never had felt any problems with the clutch, was catching on well etc.) and all of a sudden, with no warning sign or anything (no shock, ...
2
votes
0answers
43 views

MG ZS 180 - overheating clutch

So I got a new (well 2004) MG SZ 180 the other day and it turns out there is a small issue with it. After using the clutch in stop/start traffic, changing gear gets harder and harder until I end up ...
2
votes
2answers
80 views

Ford Transit not going into 1st gear easily

With a lot of Googling I've found loads of different things that could be causing this - and none for a Ford Transit so I hope someone can explain exactly what is causing this problem, and from the ...
2
votes
2answers
13k views

How to extend the life of the dual mass flywheel in a diesel engine?

I am looking for ways to improve the life of the dual mass flywheel (DMF) in my 2005 Ford Focus tdci. I have heard that they can wear out quite quickly on the Ford Focus if they are driven in city ...
1
vote
1answer
45 views

2001 Fiat punto: slave cylinder repaired brake warning light

My clutch slave cylinder was replaced today but my brake fluid warning light came on for a second on two bends. Is this more likely an electrical fault? I will take it back to the garage nect week. ...
1
vote
1answer
68 views

Achieving least wear on clutch when changing gears? [closed]

I want to do the least wear on my clutch on a manual car. I only recently passed the test and I wonder if I ever learnt to use the clutch efficiently. Here's how I change gears: foot of gas press ...
1
vote
1answer
41 views

02 renault scenic. Metallic tapping sound when engaging the clutch

The other day my wife was driving the car when it lost much of its power and she described loosing power on the left side of the car. To the point that she checked the tires for punctures. This was ...
2
votes
1answer
85 views

How to bleed Toyota Tacoma clutch system?

Vehicle: 2007 Toyota Tacoma 4WD v6 6 speed I found this tutorial on pre-bleeding but it is generic (not vehicle specific) and I think there are differences between the cylinder it uses and Tacoma's, ...
1
vote
1answer
52 views

New clutch master cylinder not filling with fluid after replacement

Vehicle: 2007 Toyota Tacoma 4WD v6 6 speed I installed a new master cylinder (the truck is at about 120K mi) but when I reconnected all the plumbing, it seems like it is not filling with fluid. The ...
5
votes
2answers
47 views

01 gti not going into reverse 1st 3rd or 5th after I changed the clutch

So I changed my clutch a few days ago and now it will not engage reverse 1st 3rd or 5th gear but will engage 2nd and 4th no problem with the car on and off. I readjusted the cables but still nothing ...
4
votes
2answers
249 views

Manual transmission difficult to put into gear. Do I need a new clutch?

I have a 1998 Jeep Cherokee Sport, manual transmission (the 6 cylinder model, I believe 4.0L). It has 4 wheel drive. I've lent the car to some friends recently who were 'rusty' with their manual ...
0
votes
1answer
88 views

Do i need a clutch replacement for my 2003 vw jetta?

I am not very good at describing car problems, but i'll try my best. My 2003 Jetta is an automatic. Here recently, while I drive, the engine light comes on. My car revs very high, even though i am ...
3
votes
1answer
267 views

Stiff clutch on Toyota Corolla: can it be adjusted?

I have a 2003 Corolla (mileage ~70K) that drives very well generally, except for one problem: The clutch has always been quite stiff since I purchased it a couple of years ago, and I think it's slowly ...
1
vote
1answer
165 views

Noise when the engine is idle

I would like to know why my car is making noise when the engine is idle, but the noise is silence when I pressed the clutch ?
3
votes
1answer
273 views

Clutch Pedal will not depress

On my 2000 Jaguar V6 3Lt I replaced the clutch friction plate and slave cylinder/thrust bearing. After bleeding the clutch, the pedal is hard frozen and will not depress. I flipped the clutch wrong ...
0
votes
2answers
65 views

All signs of clutch slipping but the car only has 48,000 miles. How can this be?

I have a 10 yr old fiat panda with 38k miles on the odometer. Manual Transmission. Within couple months I started getting all of the symptoms of the clutch slipping. The condition is worse in a higher ...
5
votes
2answers
26k views

Clutch catches VERY high, is this bad?

I have a '98 Rodeo and the clutch catches extremely high up the pedal. It's probably 1-2" down (90% up in the travel). The clutch does not slip at all and the car runs great. Is this indicative of ...
3
votes
0answers
26 views

Clutch/transmission noise [duplicate]

I have a manual transmission in a Ford Ranger with 240,000 miles and it has recently started making an intermittent grinding/grating noise. The conditions under which I have heard it are: Clutch is ...
3
votes
1answer
124 views

Foot slipped off clutch while downshifting. Damage?

I have an '08 Honda Fit with a 5-speed manual transmission. I hit a steep hill earlier today and decided to downshift from 3rd to 2nd, so I didn't ride the brake for several miles. Before my RPMs ...
4
votes
2answers
43 views

To repair or not repair?

I drive a 2005 Honda Civic DX, 166k miles. My clutch was having problems over the past few weeks, it would shudder the entire car when i would let it out from 1st and 2nd gear. It has since stopped ...
1
vote
1answer
226 views

Scooter clutch plate gets damaged/burn't for a short time

I have an Indian Scooter (Bajaj Chetak) which was bought 15 years ago. For the last few days, the scooter has been witnessing lot of problems. 1. The clutch plate gets damaged and burn't - It ...
3
votes
1answer
120 views

Will a worn clutch ever completely fail to engage? If not, what will cause this?

I've noticed my clutch beginning to slip for maybe a month or two; it was slower to engage, but not badly enough to affect driving. Over the last week or so, it was getting significantly worse every ...
3
votes
1answer
289 views

Replaced clutch on '84 Bronco 2, now clutch does not disengage

I replaced the clutch on an '84 Ford Bronco 2 (2.9L). After removing the transmission I found out that the throw-out bearing and slave cylinder were completely destroyed. I replaced both parts and ...
4
votes
2answers
588 views

1st gear hard to engage unless stopped, Subaru 2004 Impreza Outback Sport

Since I've bought my 2004 Impreza Outback Sport, I've had a problem with shifting into 1st gear. First gear is generally difficult to engage while moving. You can just force it, but it's really ...
4
votes
3answers
347 views

Did I damage my car by trying to move in reverse with the handbrake on?

I was in a hurry to leave for the office yesterday and forgot that my handbrake was engaged while starting. I started the engine, clutched, and reverse geared, and found the vehicle not moving ...