Brake systems on vehicles are typically driven by either pneumatic or hydraulic systems that multiply the force applied by an operator to slow a vehicles rate of speed through the use of friction.

learn more… | top users | synonyms

2
votes
3answers
383 views

Is an 50 ft/lb air wrench (not impact wrench) strong enough to remove brake assemblies

I can't get an impact wrench in there. Any idea if a standard 3/8" 50 ft/lb air wrench will be strong enough to remove the fasteners needing to be removed to replace the brake pads and disk ? Could ...
2
votes
1answer
224 views

Could my brake problems be caused by a wrong kind of brake fluid?

The brake light is on in my 2007 Toyota Tacoma 4WD v6. The recurring pattern has been that I would fill up the brake fluid but then it would drop below the minimum mark after just a few days. It ...
2
votes
3answers
656 views

Is this a “warped” rotor?

I am experiencing some pulsating while braking in my 99 Ford Escort. After removing the wheel and inspecting the discs they both look like this. Are the lateral lines something that could cause the ...
2
votes
3answers
247 views

How to Determine If front Brakes Do All the Work?

EDIT: I misunderstood what a brake imbalance is and confused it with brake bias. This question describes what a brake imbalance is and this question describes some causes and fixes for it. The ...
2
votes
1answer
91 views

What are the effects of not having ABS?

I recently realised that my car does not have ABS. Would my stopping distances increase? Does it make a lot of difference in good conditions (e.g dry, smooth roads)? Would it make any difference in ...
2
votes
3answers
944 views

What is the cause of a soft brake pedal after bleeding?

I installed new rear calipers on both sides, new pads on all four wheels, and bled brakes with engine off, then with engine on, two times each. The pedal is hard when the engine is off and extremely ...
2
votes
2answers
12k views

Sqealing noise from left rear wheel- very hot

I have a 2007 Mazda 6, and after cruising for a while on the highway, I started to hear a very loud squealing noise coming from the rear wheel on the drivers side. It's an extremely high pitched and ...
2
votes
1answer
532 views

How to test and repair brake imbalance?

My 2000 Honda Civic Aerodeck just failed its MOT (roadworthyness test) on Front Brake Imbalance (51%). I changed the pads a few months ago, and had trouble with both calipers on the driver's side of ...
2
votes
2answers
841 views

What can cause a stiff brake pedal that softens when stopped?

I have a 2002 Toyota Avalon. Overall the car is in excellent shape, no major issues. Recently, I have noticed the brake pedal requiring increasing pressure, but only when moving (which is obviously ...
2
votes
1answer
35 views

Specifics about changing a brake caliper on 2000 Toyota Camry

I went to change the brake fluid in my 2000 Toyota Camry and when I tried to unscrew the bleeder nipple on a front caliper it broke in half rather than unscrewed. So, I need to replace the caliper ...
2
votes
3answers
40 views

1995 Ford Thunderbird

When I step on the brake pedal I hear a hissing sound and the pedal goes all the way to the floor and the brakes barely stop the car. This doesn't happen every time but most of the time. Any ideas of ...
2
votes
1answer
349 views

What is brake imbalance? How can I fix it?

My 2000 Opel Agila 1.2 has an advisory on it's MOT saying: Front Brake imbalance [sic] high at 23% What does this mean? What's wrong with my brakes? What does the 29% mean? How can I fix it? ...
2
votes
3answers
740 views

Pontiac g6 runs lean; throwing codes

My 2006 g6 v6 3.5 is showing codes p0171, p0174, p0705 and u0073 171 and 174 show that the engine is running lean. Is this a serious issue? 0705 shows the trans range sensor a circuit 0073 says the ...
2
votes
1answer
48 views

custom built silicon carbide discs

My toyota corolla CE110 brake performance is not to the expectation, it takes an unusual amount of distance and requires comparatively hard braking to get it to stop. I had checked it by a mechanic ...
2
votes
1answer
358 views

Will the brakes wear out more on light braking?

I have a doubt. Will the brakes wear out faster on light braking? On heavy / hard braking, the tires stop faster, which means the brake pads are working for a lesser time. Will this affect / increase ...
2
votes
3answers
6k views

Steering wheel shakes when braking at high speeds

I got a 2011 lexus ES350, the steering wheel shakes badly when i push the brake. I have been told that its the rotors. I got the rotors resurfaced last week at the lexus service center but no ...
2
votes
1answer
97 views

Draining master cylinder (2005 Malibu)

What's the best way to drain the master cylinder on this car?
2
votes
1answer
104 views

How does AP Racing differential bore brake master cylinder work?

I was doing some reading on racing brakes and on AP Racing website I have found an interesting master brake cylinder: Differential Bore Trunnion Type CP8854 - Push Type The idea is to minimize ...
2
votes
1answer
37 views

I have a 1999 chevy blazer back wheel getting hot

The back wheel on the passenger side of the blazer is getting very hot, does not make any noise. The brake rotor the hub and the outside of the wheel will be hot after about 3 miles.
2
votes
1answer
71 views

Would waiting a few weeks to replace pads and rotors have damaged calipers?

I took my Volvo s60 for regular 84k maintenance a few weeks ago and I requested to get my brakes and rotors checked. I was told that they needed to be replaced. I booked an appointment for three ...
2
votes
1answer
49 views

Brakes smoke on driver side, but only after non-level terrain

I recently had my brakes serviced. Pads and rotors were replaced. Everything seemed fine. Today, I took a 30 minute drive where I applied the brakes significantly on the way back due to hilly terrain, ...
2
votes
1answer
61 views

Aveo 2012 brakes do not work when the engine is running

I have this problem when you depress the brake pedal it moves all the way to the floor and does not slow the car down. It's happen only when the engine is started. Please any fix or help. I really ...
2
votes
3answers
111 views

Brakes pads changes and cutting rotors

My brakes started vibrating occasionally when slowing down on highways at high speeds. I have been realizing that the brakes feel low. I went to a shop for an oil change and the mechanic peeked in ...
2
votes
1answer
26 views

Clicking of Brakes

My vehicle was recently in a accident involving a raccon (go figure) and did a lot of damage. I already had it checked out and they said it needed alot body work and possible wheel alignment. However ...
2
votes
2answers
6k views

The brake pedal goes down to the floor after replacing the rear rotors and pads on my 2010 highlander

I have replaced rear brake pads and rotors on my 2010 highlander and right after I went to take the car for the test drive the brake pedal goes all the way to the floor. There is no leak anywhere. I ...
2
votes
1answer
59 views

Truck: “H” brake button

I've found in different trucks and buses, etc.... An "H" button which, when pressed, activates a braking system. This system is only available when the vehicle is immobilized. Which brakes are ...
2
votes
1answer
394 views

Handbreak return spring Vauxhall/Opel Vectra

So i got in the car this morning, and it felt like i still had my handbrake on when i pulled off. Check that, it wasn't on. Drove on a little bit thinking i was imagining it, finally accepted it was ...
2
votes
2answers
1k views

2012 Ford Escape grinding noise while braking

My Ford Escape started making an unusual noise recently. Would appreciate if anyone can help me diagnose the problem. The noise only occurs when I brake and only when my speed gets down to about 15 ...
2
votes
1answer
327 views

My car pulls/stalls after i apply brakes and it makes a loud grinding sound

I have a 2002 Mercury Cougar and it makes a loud grinding sound every time i brake. Sometimes it even rolls backwards when in drive. What could be the problem(s)?
2
votes
1answer
148 views

1940 Buick Super brake master cylinder removal

I have a 1940 Buick Super. I need to remove the master cylinder to rebuild it, but the bolts turn in the frame when I try to remove the nuts. There is some kind of metal cover over the end of the ...
2
votes
1answer
764 views

Car decelerating quickly

I recently changed my brake pads and did wheel alignment at the official workshop of my car manufacturer. It was driving just fine but suddenly as I was driving it at one fine point the steering ...
2
votes
1answer
52 views

2001 Ford F150 howling when braking with trailer

I have a 2001 Ford F150 Lariat with the 4.6L V8 Engine. Sometimes while I have my trailer hooked up I get a tremendous howling while braking. Almost so loud you can't hear anything else in the cab. ...
2
votes
1answer
52 views

Braking causes steering wheel vibration

I replaced my front brake pads less than a year ago. I now am having a steering wheel vibration when I brake and believe my rotors are warped. I checked my pads and they have a lot of pad left on ...
2
votes
2answers
680 views

Rear drum brakes will not release

I have a 2010 GMC Canyon. When you first start up and put the vehicle in gear the breaks will not release.if you accelerate then it will pop and release. This will happen the first two or three times ...
2
votes
1answer
281 views

Brakes slide when pressing on them

I own a 2001 Hyundai Sonata, and when I go press on my brakes, the car will slow down, but when I press down on them hard (for an immediate stop) they slide for some reason. Is this common? I've put ...
2
votes
1answer
111 views

No resistance when depressing brakes with no leaks in system

I heard a loud pop, and now the brake pedal has no resistance. There are no leaks in the system. I tried a master cylinder and bleeding the brakes. Still the pedal goes down easy and comes up slow. ...
2
votes
1answer
382 views

Toyota Hilux Surf 1998 Stuck in Park and speedometer and odometer not working

I just bought a 1998 Hilux Surf. It has an automatic gearbox. When pressing the brake the drive selection should be unlocked, but it does not. I need to use the "red button" to unlock the drive ...
2
votes
4answers
11k views

Brakes locking up while driving

I have a Honda accord 2008 which has performed well until recently. On my may to work I noticed my car wasn't accelerating as usual; it had this feel like it was dragging. On parking, I noticed smoke ...
2
votes
2answers
157 views

Require solution to reduce breaking of tiles indoor, when operating an electric tow truck

I am using an 3 wheeled, rear drive, electric tow truck vehicle indoors on commonly used floor tiles. It seems that when braking the vehicle some floor tiles break . Its specs are similar to ...
2
votes
1answer
1k views

What brake discs does my car have?

I have a 2006 Citroen C4 1.6 VTR+ (5 doors) and I need to change brake discs and pads. I found this website: http://www.carparts4less.co.uk/ where I order those parts, but after taking them to a ...
2
votes
1answer
520 views

Ford Escort - Brake Fluid leak in car

I own a Ford Escort 1992, 1.9l, manual. Recently my default-idle had been really high and so I did some research and figured out that my brake booster probably broke. So I went to the junkyard and got ...
2
votes
1answer
2k views

Grinding sound when stopping with 2010 Honda Civic.

I've had brake pads and rotors checked. Mechanic said they were fine. Grinding noise becoming louder. Mechanic said it could be brake dust. Will brake dust continue to get louder? How safe is this?
2
votes
1answer
546 views

Motorcycle: Irregular brake bite (front single disk)

My motorcycle's front brake is giving a irregular bite. I don't know how to express it in words please check the illustration below. --------$^^^^^^^^-^-^-^-^-^^--^^^---^^^^^^----^^^| ~60Kmph ...
2
votes
1answer
487 views

Brakes and low-pitched squeak

I've had my 02 Honda CR-V for 3 months or so now and have noticed a growing squeak upon application of my brakes. This squeak is different from the normal high-pitched squeal that comes from the metal ...
2
votes
0answers
63 views

brake pedal staying down. Then ok after a few days being stood

I have a Mercedes C200 and the other day the brake pedal stayed down while I was driving. It did come back up a little as I carried on home. I haven't driven the car for a day or so. then this morning ...
2
votes
1answer
1k views

Brake fluid reservoir level drops fast to minimum but not below

The brake fluid reservoir level drops very fast in my 2007 4WD V6 Toyota Tacoma, probably within 3-5 days of filling it up. The funny thing is, it drops to just below where it says minimum but not ...
1
vote
2answers
451 views

Brake pedal bottoms out [on hold]

I have a 2004 Chevrolet Suburban. I changed the brake calipers because they were leaking. I think the brake system is working in the front but not in the back. Does anybody have a way to troubleshoot ...
1
vote
3answers
2k views

Odd brake squeak only at the very end of the stop

I have a 2003 Infiniti FX 35. It has ~130K miles on it but new front and rear brakes were put on in the last year. Just recently, after about a month of sitting around without being driven, the car ...
1
vote
3answers
278 views

Does downshifting ( Engine Braking ) help when my car brakes CAN lock the wheel?

Know facts: When your car brakes (e.g. because of the weight) can't stop the car, it's recommended to use downshift (engine braking) to help brake the car. The best way to stop the car is to brake ...
1
vote
2answers
145 views

Pump and Hold Brake Bleeding (2 Person)

I just had an issue with my brakes that was incredibly hard to find due to a sneaky leak and additionally a brake (back-passenger-side) needing bled 10-15 times. Is 10-15 times normal? My brake ...