Brake systems on vehicles are typically driven by either pneumatic or hydraulic systems that multiply the force applied by an operator to slow a vehicles rate of speed through the use of friction.

learn more… | top users | synonyms

4
votes
2answers
167 views

Is it necessary to bleed brakes if the system is never opened?

Just wondering if there is a point to bleeding the brakes if the system is never opened, since it's effectively a closed system. For example, does the chemical change should the fluid reach boiling ...
4
votes
2answers
382 views

Honda Civic braking problems in warm climate

I have a 1991 Honda Civic wagon that loses braking power on hot days. I have it working for the initial press, but as I hold down the brakes I slowly lose braking. I have to repeatedly press at red ...
4
votes
2answers
6k views

Honda Accord bubbling / gurgling sound when braking first few times

I have a 2009 Honda Accord. All 4 brakes were recently serviced so I don't think this is related to pads or rotors needing attention. When I first start driving, when I hit the brakes, there is a ...
4
votes
4answers
3k views

1972 Toyota Land Cruiser FJ40 Disc Brake Conversion

I just bought a '72 FJ40 and realized that three out the four (drum) brake cylinder's are seized and one of the grease seals is leaking bad. Since I have to replace the brake cylinder's, I am ...
4
votes
1answer
32 views

My Jeep is making a squeaky noise when I apply the brakes and when I drive slowly it makes a clunking noise

I have a 2002 Jeep Grand Cherokee Laredo. I just bought it two weeks ago so I don't know much about it. They guy I got it off of said it has brand new brakes, rotors, and calipers. When I apply the ...
4
votes
2answers
271 views

Brakes not working after being parked up for 3 years on Jeep Grand Cherokee

After parking my jeep Grand Cherokee 1997 for 3 years, I've decided to get it back up and running. My problem is that the brakes are not working. I can pump the pedal but then it looses pressure ...
4
votes
1answer
89 views

02 chevy cavalier skidding when braking

So I've done a lot of under body work on my 02 Chevy cavalier z24, the most recent being the sway bar, rack and pinion and last week the struts. Around the time we did either the sway bar or the rack ...
4
votes
4answers
15k views

How far should you put your handbrake up?

My feeling is to just pull it up as far as it goes, but I've heard this is bad for the brakes and the car and so it would be better to pull it up with the button pressed till you feel slight ...
4
votes
1answer
37 views

Wheel rubbing/tight at one point per wheel revolution

On my 2005 BMW 320D, I recently (200 miles/1 month ago) noticed a rubbing noise coming from the front passenger side wheel. It is only really noticeable on smooth tarmac at slow speeds, but I did ...
4
votes
1answer
38 views

Ticking sound when stepping on Brake [closed]

I have this ticking sound somes when I press on the brake while is not moving and on Parking but the Engine is on.I changed the rear rotors, pads , and the right rear right caliper, but the sound is ...
4
votes
1answer
75 views

Car doesn't like ceramic brake pads

I used to have a 96 Nissan Sentra with 1.6l. I had the car for a very long time and did at least 3 brake jobs on it. Every time i would change the pads and rotors I would try using ceramic brake pads. ...
4
votes
2answers
91 views

Loud High-Pitched brake squeal

I have a 2005 Toyota Corolla with squeaking from brakes. Details: Very High Pitched Worse when wet / rainy Only happens within certain peddle range (stops if I press soft or real hard) Steadily goes ...
4
votes
1answer
43 views

Trying to order a part, shows up brake knuckle spindle assembly, but all are used for 98 civic? [closed]

I'm trying to order the hub assembly and brake knuckle spindle assembly for a 98 Honda Civic so that I don't have to do any press work with the bearings. On other vehicles the parts can be bought new ...
4
votes
1answer
96 views

Finding brake parts

I'm working on a 1963 Chevy Impala. I am rebuilding the drum brakes, but I can't seem to find all the parts-- some have gone missing over the years. Is there anywhere to find all the internals in ...
4
votes
4answers
14k views

Squeaking brakes on motorcycle - an issue or not?

The front disc on my motorcycle emits a low pitch squeaking noise when I'm pulling up to a complete stop (almost like the sound train brakes make when pulling up to a station). This only happens when ...
4
votes
1answer
1k views

Rear Drum brake scraping and brake pulsating

I recently had a lug nut stud replaced on one of my rear tires. I believe they had to take apart the drum brake to remove the old stud and install the new one. That same day I heard a scraping which ...
4
votes
1answer
631 views

Ford Escape - Loud Brake Sounds in Reverse

2001 Ford Escape. I've recently had some work with the transmission done, but in the past 2 weeks or so, whenever I brake while in reverse, it makes a loud grinding sound. However, I've looked ...
4
votes
1answer
40 views

Brake judder on new rotors

2013 Corolla have replaced front pads, rotors, pistons, bled fluid, still rotors overheating causing 'judder' when braking?
4
votes
1answer
45 views

2012 vw jetta rear brake shoes

I replaced rear shoes and drums on my 2012 jetta got the shoes on but new drums will not go on is there any kind of adjustment to get the drums to go on freely
4
votes
3answers
162 views

Rumbling sound from brakes in Lexus

My family has a 2013 Lexus RX 350. Today was the first time we noticed a low rumbling sound coming from the brakes when they are pushed. We've had a maintenance check with no issues a month ago. Any ...
4
votes
2answers
232 views

Brakes smell, car pedal hard, light smoke, slows down during gear shift

3 weeks ago I bought a car from a private dealer. When I tested it out, the car was completely fine. Not to long ago after, I noticed that my back tail lights were on and figured out it was the braker ...
4
votes
1answer
52 views

Strange electrical issue with after market brake lights

I've got a 1991 Jeep Wrangler. About 3 years ago I put LED brake lights on. They worked great until just a couple days ago, when the drivers side stopped working. Shortly after, they started working ...
4
votes
2answers
309 views

Modest braking sounds similar to squealing tires

When I'm braking at a stop sign, I'm hearing a sound that sounds like a high pitched tire squeal; it's like a mix between tire squeal and the constant chirp from a bad belt, and it's coming from the ...
4
votes
0answers
33 views

Mazda CX7 metallic pulsating sound when driving below 20 MPH

I have this issue with my CX7, when I drive at a regular speed, the car performs very well. Now when I release the gas pedal and brake the car makes no sound until it goes below 20 MPH, then I can ...
4
votes
0answers
37 views

2002 Ford Taurus E brake light on dash stays on

2002 ford Taurus. e brake light on dash stays on. removed, checked e brake pedal switch with volt / ohm meter and it works. found and pulled the fluid sensor under master cylinder. pulled pigtail, ...
4
votes
0answers
65 views

The brake pedal goes to the floor after starting the engine [closed]

I am currently in the process of rebuilding a wrecked truck. I have replaced all of the - brake lines - calipers - wheel cylinders, - pads, - shoes, - brake booster, - master cylinder However ...
4
votes
0answers
24 views

Brake squeaks on 2013 Cruze

I was told that the brakes on the 2013 Chevy Cruze would squeak if the rotors had condensation etc. They had already resurfaced front rotors, adjusted and cleaned the rear pads and told me basically ...
4
votes
0answers
200 views

Long brake pedal travel after replacing pads

I recently installed new brake pads. They haven't been bedded in yet and I don't intend to use them for daily driving. The pressure feedback from my brake pedal progressively increases as I apply ...
4
votes
0answers
146 views

While driving, my handbrake gets automatically engaged (maybe)

I own a Hyundai Accent. I drove it for around 800kms yesterday. All was fine until I was close to my house. I heard a noise coming from the rear wheel as if the wheel was stuck. After a while, ...
3
votes
2answers
386 views

Why is martensitic steel used instead of grey cast iron for ATV disc brakes?

Grey cast iron has better thermal properties -- conductivity and specific heat -- lower density, better castability, and better friction than martensitic stainless steel. Why are OEM parts made of ...
3
votes
2answers
4k views

Pressing brake pedal during vehicle operation feels “choppy” ?

I am driving a 2004 Chevy Impala. When coming to a stop, I press the brake pedal, and I can feel the choppy vibration on the pedal. It's same regardless of weather. Should I get this checked out?
3
votes
2answers
749 views

What could cause a metal-on-metal noise when braking only while backing?

I have a 1998 Acura Integra with 204k miles on it. Some mornings after the car has been parked in my driveway facing up a slight slope overnight with the handbrake set, the first time I apply the ...
3
votes
3answers
205 views

What are the different types of disc brakes

I have head of Ventilated Disc,Carbon Ceramic disc. I do not know what are the different types of disc brakes available on the market. Which one should I choose. I would also like to know the ...
3
votes
2answers
50 views

Should I replace the disc?

Recently, my car began to make very loud noises whenever I used the brakes. At first, I didn't suspect the brake pads because I thought they were still able to undergo a few thousand kilometre. To be ...
3
votes
2answers
1k views

C-clamp stuck in brake caliper

I'm a first timer replacing (front) brake pads in my Nissan Pulsar 1.8 (hatch). I had problems removing the caliper bolts on both sides - after successfully removing them, I removed the old pads and ...
3
votes
1answer
173 views

Why does my brake pedal go to the floor when i start the truck up?

My Ford F250 4x4 brake pedal goes to the floor when you start the truck and stay's to the floor until you shut the engine off then it returns? The brake booster, master cyl, rotors, pads, brake lines, ...
3
votes
2answers
19k views

Clunking sound at back of car when applying brakes

Since having my tires changed, I've been hearing a clunking sound from waht sounds like the back driver side of my car when I apply the brakes if they're applied jsut enoug to start slowing down the ...
3
votes
1answer
108 views

Spongy brakes after brake pad swap - moisture or bubbles?

I changed the rear brake pads on my BMW last week, following the steps outlined in this video. Unfortunately the brake pedal now feels spongy. The pedal feel was firm prior to the brake swap, so it ...
3
votes
3answers
4k views

Disc brake damage, how can it happen?

I bought a brand new 207 '12 and its done its 1000mile checkup. During this i told them there was a horrible grinding noise comming from when i was breaking, even a metal on metal screech sometimes?? ...
3
votes
2answers
4k views

2005 Scion tC - Handbrake indicator light intermittently turns on

The handbrake indicator light on my 2005 Scion tC intermittently turns on while I'm driving. I've read about two causes: low brake fluid and (not likely) the handbrake is somehow getting lifted while ...
3
votes
1answer
2k views

Front wheel scraping noise

I have some weird scraping/rubbing noise in my right front wheel. I I hear it regardless of weather i brake or not, and the slower i go the more low pitched and grindy it sounds. It continues to ...
3
votes
2answers
338 views

Brake Fluid Leaking out of Master Cylinder but on Top of Booster

I have a 94 Pontiac Bonnyville that's leaking brake fluid. Recently the brake warning light came on and I noticed the fluid was low. I filled it again but it's slowly leaking. The fluid is leaking at ...
3
votes
2answers
824 views

Front, driver-side wheel sounds like it's skidding when braking

I have a Nissan Micra (UK, 51-plate, 2001 model) and I've today noticed a sound a bit like skidding when I apply the brakes, gently, around 30mph. Driving and steering as usual is fine, no unusual ...
3
votes
3answers
65 views

I have replaced my brake cylinders, but the brake pedal goes to the floor

I have a '07 Silverado. Both rear wheel brake cylinders blew apart. I fitted new ones along with new shoes. I have bled the brakes but my pedal still goes to floor. What else can I do?
3
votes
2answers
160 views

How to cleanup disk brake rust rings

Some years ago I replaced the stock rotors for slotted and drilled on all four wheels of my 2003 Monte Carlo. At the time I needed to replace the rotors and they had a habit of warping. The new ...
3
votes
1answer
104 views

Brake fluid gone, rear brakes out. '99 pathfinder

The other day I started my car and the e-brake light stayed on after releasing it and I figured it was electrical at first. When I started using the brakes I realized I had to push about twice as far ...
3
votes
2answers
152 views

2006 Pontiac g6 rough idle and intermittent spongy brake and starting issue

I have a 2006 Pontiac G6 with 160k on the 3.5 motor. Around 155k the brake pedal went hard and spongy. Also, about 1 in every 40-50 times I start it cold, the starter will turn without a successful ...
3
votes
1answer
2k views

Chevy Cruze with a funny sound when applying the brakes. The drums, pads and shoes among other things were replaced

When applying the brakes on my 2013 Chevrolet Cruze, a loud funny noise happens. I'm frustrated that this is my first vehicle I have purchased on my own and all I can think is it's just my luck. I ...
3
votes
2answers
876 views

Brake Pedal Requires More Distance to Push

My brake pedal requires a further distance to push than it used to. This is not to say it's harder to actually apply the brake; it's just that when I apply the brake, the pedal goes further back than ...
3
votes
1answer
749 views

Rattle in my left tire area everytime I brake slowly from more then 80kmh (50mph)?

I have a Chevy Cobalt 2007, and it has been doing this for a while. If I press the brake a little harder, the rattling stops. It doesnt rattle until I press the brake. Leading me to believe there is a ...