Take the 2-minute tour ×
Motor Vehicle Maintenance & Repair Stack Exchange is a question and answer site for mechanics and DIY enthusiast owners of cars, trucks, and motorcycles. It's 100% free, no registration required.

This is an issue I've had off and on for, embarrassingly, at least a year:

On misty or wet mornings, everything starts out fine but, a few minutes into the drive (like clockwork. I even know the lights it will happen at), the Check Engine light will flash for 3 seconds and the car starts to struggle as if it was about to stall if I am going slowly or stopped. Driving again, it goes away. Approach another stoplight, hello car shudder. This goes on until about 10 minutes in once the engine temp hits the perfect 90 in the middle. Boom, problem 'solved'.

I would love to know what I should be looking at to fix here. I had previously been told to start the engine while cold late at night in the dark, to look for visible arcing that disappears once the car heats up. Alas, could not find anything. Granted, VWs hide all the important bits, which further complicates things.

Local VW dealers are scammy, so I'm searching for an out of town one to replace them. That said, I'd love to at least have a clue going in so that I'll be less likely to get ripped off again.

share|improve this question
1  
Is this the 2.0L or the VR6 engine? –  Sumo Aug 9 '11 at 3:50
    
Did you ever get an answer on this question? I have the exact same problem, but it does not have to be wet out side, so I do not believe the comments about water being the issue are correct. I think it is a bad sensor. It only happens when it is cold in the morning, the car starts fine, idle fine and then about six blocks away it starts to almost stall, kind of like when the fuel pump goes bad, but that is not the problem. When the car is warm there is no problem at all. It is very odd. I thought it was one of the coolant sensors in the coolant flange, but replacing them did not fix the proble –  John Jul 2 at 2:05

4 Answers 4

Though I may not be correct, have you tried opening your hood and using a spray bottle of water on your spark plug wires? Lightly mist around where the wires connect on both ends of the wires, and maybe a few squirts around on the wires themselves. If the vehicle stutters, it may just be that the wires need to be replaced...

share|improve this answer

First step, I would take the car to a less annoying shop to ask them to read the OBD code - I would assume that there is one to read if the CEL has been on or flashing. Almost any shop will read the code for you at for a nominal / free charge.

If you would like to know the information on your own, the code readers are common items on Amazon.

I would get that piece of information first before you try anything else.

share|improve this answer

You didn't mention which engine is in your Jetta, but the Mk IV VWs, especially the VR6 engine, are known to have brittle ignition coil housings that crack and admit water, which leads to misfires.

After the engine has run for a while, it burns off this moisture and it starts running fine again. Some VWs were subject to a recall to fix this issue.

Based on my experience with these cars, the coil would be the first place I'd look. Your description is textbook for a cracked ignition coil housing.

share|improve this answer

You've almost certainly got a dodgy sensor somewhere. As Bob Cross says, the best way of locating this is to get the OBD-2 code from the ECU, which should tell you which one it is.

I am surprised that it only starts a few minutes in, most such problems I have come across start almost straight away, then go away once the engine warms up. What is happennig is that water is getting into the sensor, or the wires doing to it, and causing it to report an incorrect warning - Once the engine warms up, the water evaporates, so no more problem. If you can identify the sensor in question (I would guess Airflow, fuel or crank position), you may well find that there is a rubber seal or cover that has perished to allow condensation in.

Disconnecting each suspect sensor and cleaning the contacts with a bit of fine sandpaper may well help too, as chances are the contacts will have corroded under the condesation.

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.