Take the 2-minute tour ×
Motor Vehicle Maintenance & Repair Stack Exchange is a question and answer site for mechanics and DIY enthusiast owners of cars, trucks, and motorcycles. It's 100% free, no registration required.

This is not with the intention of saving fuel (as I have seen many answers assuming savings in fuel while doing this). But I have this habit of putting the vehicle into neutral before approaching stops (red lights). The main reason behind doing this being, is to reduce the strain of holding the brake pedal.

One of my friends is arguing that it's not good for the transmission system, shifting the transmission from D to N while the vehicle (with automatic transmission) is moving. I couldn't agree with him, as I couldn't find any issues with this. Also I couldn't find any information regarding the same on the manual for Toyota Corolla.

Do you guys have any technical details about this?
Thank you in Advance.

share|improve this question
I believe WRT manual transmissions, the idea was to reduce wear on the clutch and use the brakes instead, which are far easier to replace. –  Drise Jul 11 '12 at 0:34

3 Answers 3

up vote 5 down vote accepted

Being in Neutral or Drive should have negligible to no effect on the distance the vehicle travels when the accelerator is not pressed because the torque converter disengages the engine below predetermined RPM levels.

However, if you somehow were to push just a little too hard and sent the transmission into Reverse instead of stopping in Neutral, you would most likely be faced with purchasing a new transmission.


Rafi: If, by your question, you mean to say that you put the transmission into Neutral while waiting at a stop light, then this would not harm the transmission in any way.

Though it will not harm your transmission to shift into Neutral while your vehicle is in motion, the additional wear on your brakes by leaving the transmission in Drive will be negligible over the life of the brake pads. It is that minor.

share|improve this answer
WRT "reverse", this isn't true on modern cars. Mythbusters did exactly this and showed that putting the selector in reverse put the transmission in neutral to no net effect. dsc.discovery.com/fansites/mythbusters/db/transportation/… –  Bob Cross Jul 10 '12 at 18:47
Unless automatic transmissions have changed recently, and being in D definitely changes the amount of motion when you take your foot off the brake while the car is at rest. I'm a little interested to know how you've experienced anything else! –  Colin K Jul 11 '12 at 17:05
Isn't it also true that in most modern cars, you are unable to accidentally push the shifter into reverse without pressing some sort of unlock button, as you would to take the car out of park. –  0x7fffffff Jul 15 '12 at 10:47
Colin, my information is in reference to a vehicle moving at speed. You are talking about a stopped vehicle. These are different states for the torque converter. –  jp2code Jul 15 '12 at 12:21

NEVER, EVER go into neutral while slowing down to a stop, for 3 reasons: 1. You lose the added benefit of engine braking if the car's not in gear 2. If you have to quickly avoid something by accelerating and moving out of the way, you'll hit the gas and won't go anywhere 3. If the light turns green before you come to a complete stop, you'd have to go back into drive while moving. And you should only go into drive when stopped, really, really bad things may happen to your transmission if you shift to drive while moving.

share|improve this answer

I do this quite a bit, actually, and I don't think there's any difference in shifting from drive to neutral when the car is moving or stopped. The reason is that the torque converter is hydraulic, so it gives you transmission some slack in order to let it shift, just as if you were pushing on a clutch. The shifting cannot possibly put more wear on the trasmission that the transmission shifting between 2 and 3, for example, something that it does thousands of time in one year. In fact, going into neutral probably puts significantly less wear on the parts than that, since you're going from a configuration where gears are engaged into a configuration where they are not.

P.S. The reason I shift into neutral at stop lights is that my car vibrates quite painfully when in drive and stopped. I haven't been able to figure that out yet, but that's another post.

share|improve this answer

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.