Take the 2-minute tour ×
Motor Vehicle Maintenance & Repair Stack Exchange is a question and answer site for mechanics and DIY enthusiast owners of cars, trucks, and motorcycles. It's 100% free, no registration required.

I own a Toyota Soarer SC300 (1994), 2JZ motor non-turbo 3 litre engine. The engine is probably irrelevant, but provided for prosperity. Anyway, the front rotors were machined and are within the legal limit and my rear rotors were replaced, as well as 4 sets of brand new Bendix brake pads.

This will all done about 3 months ago. I am not a heavy driver, nor am I a heavy braker either. However recently my brakes have started squealing really badly, a high pitched squeal which hurts your ears. It doesn't happen all of the time surprisingly, just a lot of the time.

A friend told me that it could be brake dust or even dirt causing it as his does the same thing sometimes. Should I be concerned about this and what can I do about it? Surely my front rotors haven't worn down or brake pads worn away already.

share|improve this question
1  
+1 for owning a soarer! stop messing around with your brakes and get the GTE swap! –  NoCarrier Mar 9 '11 at 3:12
    
I would love to, but the money situation at the moment isn't permitting anything of the sort at present :( saving up for a house drains your pockets dry. –  DigitalSea Mar 9 '11 at 4:22
add comment

5 Answers

up vote 9 down vote accepted

You're going to have to bed the brakes in properly. Be very careful.

http://www.zeckhausen.com/bedding_in_brakes.htm follow these instructions (at your own risk). A friend had a similar car as yours (IS300) and had the same problem. Once I bedded the rotors in, noise was minimized.

share|improve this answer
    
Wow, I didn't know about the whole bedding thing. I'm guessing my mechanic forgot that (by the looks of it) important step to make your brakes last longer and function correctly. –  DigitalSea Mar 9 '11 at 4:24
add comment

I had this happen in my 2003 acura tl after getting cheap brakes at Midas. I believe its because the pads were not the same material as it should have been such as ceramic vs semimetallic.

share|improve this answer
add comment

You could try applying anti-seize lubricant to the backs of the brake pads. Also consider lubricating other places where the brake pad backing plate could rub against the caliper. Just make sure to keep it off the braking surfaces.

This has the side benefit of preventing the pads from rusting onto the caliper, making future maintenance easier.

I typically use this:

http://www.permatex.com/products/automotive/lubricants/specialty_lubricants/Permatex_Anti-Seize_Lubricant_a.htm

Someone already mentioned this in passing, but I thought it worth describing in more detail.

share|improve this answer
    
Very good to know, I might get some and see if it makes a difference. I've set to clean out any dust or objects yet, but will try everything suggested. Thank you for answering. –  DigitalSea Mar 9 '11 at 23:47
add comment

It's probably that the pads need bedding in as NoCarrier says. However, my sister-in-law once had her brakes start squealing even though there was plenty of pad left, and the problem ended up being a small stone that got stuck between the pad backing plate and the rotor, in front of the edge of the pad.

share|improve this answer
    
Ah, yes. I've heard stones can get wedged in there, and brake dust can build up causing it as well. Might not hurt to flush some degreaser onto my pads to clean out anything that might be on them. –  DigitalSea Mar 9 '11 at 12:24
add comment

I had this same thing happen with a 98 Ford Escort. I also tried all the anti-chatter/noise goo they sell at the parts stores. Nothing worked, until I replaced the pads with ceramics. Be warned though, that they may accelerate the wear of your rotors. For me this wasn't a deal breaker as the brake screech was intolerable.

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.